Having problems with your Hoover Vacuums ?

Hoover SteamVac F7222-900 steamvac Brushes do not spin. Looked at filter as per manual instructions but it was free of lint. Need to fix it, help please? Vacuum was used less than 10/12 times


Answers :

Solution for Hoover SteamVac (F7452-900) brushes not spinning
\015\012Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem should not happen as often as I see other people also having this problem. Must be a poor design on Hoover’s part. It takes about 30 minutes and a Phillips screw driver and wrench. Pretty easy, just have to remember what screws went where.
\015\012Remove brushes, and front suction cover
\015\012On the bottom of the machine:
\015\012Remove the 4 screws behind brushes which attach the top faceplate
\015\012Remove the 2 screws from base in the sunken holes
\015\012Remove the two long silver screws from base which connect all the way to turbine assembly
\015\012Stand machine upright
\015\012Remove the floor select switch handle
\015\012Remove 1 screw near the center beside the intake hole
\015\012Remove the 2 screws over the rear wheels
\015\012Remove faceplate cover, the front will need to be gently pried over the clear plastic part, be careful about the upright disengaging lever under faceplate, move it under the metal wire
\015\012Remove the 2 screws in the front of the turbine assembly
\015\012Remove the 2 hoses on either side
\015\012Disengage the bar on the floor selector switch
\015\012Pull out the turbine assembly
\015\012Remove the 4 screws and 3 clips to separate the assembly
\015\012Remove the filter (which is most likely clean since, cleaning this is the manufactures only solution)
\015\012Remove the large white gear and with a wrench remove ball bearing
\015\012Remove other large white gear
\015\012Note that the metal gear attached to turbine will not move (this was my problem), with a wrench gently grab metal gear and twist free. Spin turbine to make sure it moves freely.
Put everything back together again and you should be good to go.
I followed Mark406's advice from the above post and easily fixed my Hoover Legacy Steamvac. The turbine was stuck and just needed to be turned and freed up. Great post Mark406, good easy to follow instructions. This repair only took about 30 minutes and I was finished. My only gripe is that this can happen so easily in the first place.
Repair Help & Product Troubleshooting for Hoover Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover SteamVac F7222-900 steamvac Brushes do not spin. Looked at filter as per manual instructions but it was free of lint. Need to fix it, help please? Vacuum was used less than 10/12 times


Solution for Hoover SteamVac (F7452-900) brushes not spinning\015\012Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem shoul ... Hoover Vacuums

Hi, I bought a Homedics toe touch weighing scale about 12 months ago (or less). I don't use it that often but a short time after I'd bought it it has started give inaccurate readings in terms of weight or no weight readings at all and just gives me the 'Err' message. I have changed the batteries but this doesn't seem to help neither does using it on a hard surface. Any ideas - I haven't kept the receipt so can't take it back! Regards Eleanor Kirk


... Homedics Vacuums

I am an athletic coach and use four Terrain 550 radios and assistants to help coach, moniter and time athletes at various distances away from me. I would like to be able to communicate with the athletes directly, both ways, but have not been able to find a suitable headset unit to use with these radios. Please can you arrange to supply or recommend some headset units compatable with these radios? Even better, units with mikes to enable the athletes to run relatively hands free. Many thanks f


You can try these links 1. http:// ... Vacuums

I can see the height adjuster under my Bissell pet hair eraser vacuum, but it doesn't adjust. The parts don't look like they're touching. It's been iffy since I took it out of the box. Now it doesn't adjust at all. Used only five times. Looks like I should be able to fix it myself. No local repair available. Could you help please?


Http://uk.bissell.com/images/UserGuides/3920E_508.pdf\015\012\015\012This is the pdf manual. If you look at page 12 you'll see that the bo ... Bissell Vacuums

The powerhead on my Dirt Devil keeps cutting out, and after a few minutes, making a burning rubber smell. Only used it less than a dozen times (same thing happened with my Hoover!) It is free of hair etc...


Sounds like you've done a lot of troubleshooting on this unit. It could be that the bushings are worn and the "play" in them is causing them to seize (this is often accompanied by a chattering sound from the bushings).\015\012\015\012I w ... Vacuums

I purchased the Shark Steam Mop less than a year ago and I have used it about 8 times and now it is not working. It will not steam. The light on the front is on and you can hear it tryng but it will not get hot and steam the water like it should. I think it needs to be replaced with a Warranty Item for free. It is still under warranty.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

The brush on my Electrolux Ambassador III vacum stops turning after vacuming for only a few minutes every time I use it. The power nozzel is less than a year old and except for the brush not wanting to turn, it operates just fine. Any suggestions on how to fix the problem?


... Electrolux Vacuums

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.


First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected und ... Vacuums

No manual Hi there my bissell will not **** up the water its been some time ago that I used it and it has not been used more than 2or 3 times can any one help me with this. I have also miss placed my manual and instruction this does not help me either .So if any one can help Id be a happy woman with clean floors thanx Vickie


Link to the manual download - http://www.bissell.com/Product_Search.aspx?Criteria=1699\015\012CHeck to see if the front of the unit is clogge ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Whistling noise I just bought Dyson dc 33 multi floor plus about a month ago and use it 6 times because the carpet get dirty / dusty so quickly living with 5 other people in the house and when I use it today by stepping on the foot thing to make it to go down and when I push the botton it makes the whistling sound why is it like that I have read every instructions several times , does that mean I need clean the filters or need to get it fixed . When I first used the vacuum it was not like that a


... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

The problem is that the cleaner is heavy to use and does not pull itself forward as it should. It has been back to the supplier 3 times but they have not fixed the problem. The LED's on the front flicker and I think it may be a problem with the sensor. If you have any info. on how the sensor works and where it is located it would be useful as well as any other suggestions to fix the problem please.


If it heavy then do some muscle work and body building ... Vacuums

My electric toothbrush doesnt work any more even though I have only used it a dozen times. I have obviously tried to charge it, but with no result.I disposed of all the packaging when I started using it so I dont have the guarantee. I bought it from Tesco in Roundhay Rd., Leeds 8. roun about Christmas time. I would be grateful if you could help me with this matter. Yours sincerely, Mrs. L.E.Glenn


My Dear Chap. It is highly unlikely that you can exercise any type of warrenty for the toothbrush without the documentation. That is, a reciept at the least. Packaging would have helped, but the receipt is the key.\012What you can do is try to ... Vacuums

I have Bex Bissell Proheat. It is one problem requiring fixing each time I use it. Just had a new pump fitted as water not spraying out. Now the water is not being sucked up. For the money this has not been a good product. When it works it is good. But the constant issues each time it is used is frustrating.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I just bought a shop vac to **** up the winter slop in the garage. the first time I used it, it worked perfectly but the 2nd and 3rd times I used it, it spits water from the exhaust. Why? It doesn't seem to have a plug/clog and I have the foam sleeve plus the circular paper filter on it, as per directions. Help!


Too much water in the unit causes what you describe. Water should be drained and the unit completely dried between water events, or unit will rust and have shortened life. ... Shop Vac 925-13 Canister Wet/Dry Vacuum

My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing


No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Fantom Upright Vacuum Cleaner Model FM 760 H used one time. Starter would not work when I tried to use it the second time. Starter doesn't make any sound at all when pushed. Help! Thanks!


... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

I have an euro-pro steam cleaner model # sc505 that is about 2 years old. It has only been used a limited number of times, about 3 or 4 times. It now has a tightly sealed safety cap on it and it will not release allowing me to add water to the steamer to use it now. Any tips on fixing it? I'd love to have a products guide to items that are available for compatiability with our sharkie. We constantly see new items available and wonder will that product work with ours?? Thanks!


... Euro-Pro Shark SC-505 Handheld Steam Vacuum

I got a vacumn from a friend who ungraded and though i used at her home when i got it home it would not turn on when plugged in and i check everything and no use. my friend lost her manual. im in my 60's and on a disability fixed income so cant afford to take to repair but got lots of men at church who would help if they know how to trouble shoot it. and would really appreciate any help. thank you , ann


Hi\015\012In the UK we have similar machines but they are made by Vax. If you can't source the correct user manual from Hoover.com consider the following - it is a free download.\015\012\015\012http://www.vax.co.uk/downloads/pdf/vzl-60156016_v2 ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

The clock changes for daylight savings time on the wrong day. it did this the past few times the time had changed. the date on the back of the unit is 2004. didn't they move the weekend of daylight savings time a few years ago, can you help me fix it or do i just deal with it?


Daylight Savings Time was extended in 2007.. (the Act was in 2004).. \015\012\015\012So your clock worked fine for three years.. now.. if you can turn this automatic feature off I suggest you do and just set it manually... otherwise you ... Vacuums

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!


Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

We have a series 90S, 2.5 gallon Shop Vac. We used it for the first time to try and **** up water in the basement. Each time we turned it on, it would shut down after collecting less than 1" of water. We had to remove and squeeze out the foam sleeve each time, before it would work again (nowhere near 2.5 gallons!). Any ideas? Is the plastic sleeve that can move up and down inside, the float (poorest manual I've ever seen!)? Should there be a ball float that we're missing? Thanks for any s


Remove the foam sleeve when using the unit to pick up water.\015\012The float is in there to indicate when the unit has "enough" water in it. The float rises with the amount of water and when the water reaches a certain height the float is "pulled" ... Shop Vac Vacuums

I have a Hoover Wind Tunnel that has been used twice both times at Christmas to pick up pine needles. It really has never been used because my cleaning ladies come every week and use their own machine. The problem I have is that the machine just doesn't pick up anything. Can you help. It's not overuse that is the problem!


You may have the ductwork of the cleaner plugged up with the pine needles. First, unplug the hose from the cleaner and find if you have suction into the bag. If so, check the hose and ducts for blockage from the pine needles. ... Vacuums

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hi, I have been given a beautiful Husqvarna Prisma 980 and the power seems to have stopped getting to the machine.. The first time I plugged it in it worked, all the lights came up where they are supposed to, then the second time nothing =( Some help would be appreciated as I would like to fix it instead of throwing it in the bin Thanks Vicky


If you're really serious about getting this machine running, you need a service manual. Here is a .pdf download manual:\015\012 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0668 seconds