Having problems with your hoover windtunnel ?

how do i fix height adjustment on hoover windtunnel

is stuck in one position

Answers :

Repair Help & Product Troubleshooting for hoover windtunnel

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Height adjustment on Hoover Windtunnel u5755-900 no longer works


On this model it is only a single slide adjustment lever. have you trie to tilt the vac backwards (lifting the wieght off the front wheels) and then slide the adjustment lever?\015\012\015\012If there is a mechanical issue with it. take t ... Hoover Vacuums

Height adjustment won't work on Hoover windtunnel


In my experience, Hoover height adjustment are "stops" rather than being attached to an axel. Look for something that rould resemble a set of circular steps somewhere in the path the axel would take as it goes up and down. It is usually on the unde ... Vacuums

Hoover u6476 Windtunnel nozzle height adjustment cam repair


... Vacuums

Hoover u6476 Windtunnel nozzle height adjustment cam repair


... Hoover Vacuums

I have a WindTunnel Hoover vacuumn that is less than 1 year old. The on-off switch is worn out and the carpet height adjuster does not connect. Where is my closest service center? (So I can use my warranty) My zipcode is 58203. My phone number is: 1-201-791-3492. My email address is: [email protected] Of course, I need help as soon as possible. Thank you, Audrey Cooper


According to Hoover's web site the closest service center is \015\012\015\012\015\012\015\012MJB MAYTAG HOME APPL CENTER \015\012418 BELTRAMI AVE NWBEMIDJI MN 56601 218-751-2420\015\012which appears to be over 100 miles from you. I have ... Hoover Vacuums

How do you fix the height adjustment on hoover convertible vacuum


... Hoover Vacuums

I have a Hoover Windtunnel Model #U5456-900 that appears t be stuck in the lowest postion. When I take apart the brush assembly, I do not see anything that the sliding level moves to adjust the height. Can you help?


... Hoover Vacuums

Hoover Windtunnel smells like burnt rubber replaced belts brush doesn't spin when placed on carpet height adjustments won't move


Sounds like you have a bad brush roll(48414115), take it out and see the the ends turn freely or not, if not, then replace it. Also check the the slots that the brush roll sits in to make sure they haven't melted. I am assuming that the ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel carpet level adjustment


The suction is so great that it sucks up your carpet, then nothing works. I get my children to stand on the corners/edges of the rug so that it stays perfectly flat on the floor while I vacuum. Or, you can turn off the brush roller (set it to "har ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover U5456-900 height adjustment repair


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I can see the height adjuster under my Bissell pet hair eraser vacuum, but it doesn't adjust. The parts don't look like they're touching. It's been iffy since I took it out of the box. Now it doesn't adjust at all. Used only five times. Looks like I should be able to fix it myself. No local repair available. Could you help please?


Http://uk.bissell.com/images/UserGuides/3920E_508.pdf\015\012\015\012This is the pdf manual. If you look at page 12 you'll see that the bo ... Bissell Vacuums

My telescopic wand height adjustment won't lock the height in place. The wand extends to full height with no locking in place. How do I fix it?


These wands have a very small nub that locks them into place. They wear out very easily. You might have to replace the wand. ... Euro-Pro NV31 Infinity Vacuum

Height Adjustment on Hoover Wind Tunnel doesn't seem to do the job.


... Vacuums

How do you reattach the front rollers on hoover elite rewind so that the carpet height adjustment works


... Hoover Vacuums

The height adjustment isn't working...it isn't changing the height at all...how can I fix this?


... Dirt Devil M086700 Vision Bagless Upright Vacuum

Hoover model U6425 height adjustment - Hoover Elite U5061-900 Bagged Upright Vacuum


... Hoover Elite U5061-900 Bagged Upright Vacuum

The height adjustment on my Bissell 6594-W no longer works, I took it apart and reassembled but still doesn't change the height. Should there be a spring in there? Is there a site with directions on how to fix it? Thank you.


... Bissell 6594 PowerForce Bagless Upright Vacuum

Height adjustment on hoover elite supreme


... Hoover Vacuums

Hoover auto height adjustment not working


... Hoover Platinum Collection Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt


I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

How to fix cord jammed on Hoover Windtunnel uh70215?


... Hoover Vacuums

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?


This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?


Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum

I've had the Hoover Windtunnel for a couple years now. Its starting to smell when you vacuum. Why and how do I fix it???


I was experiencing the same problem right after changing the belt for the first time, as my Hoover is just a few months old. I am assuming what you are smelling is burnt rubber, like your belt, right? Well, if you have changed you ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0621 seconds