Having problems with your Hoover Windtunnel Supreme U5280-900 Upright Vacuum ?

The suction has decreased by about 50%. The brush

\015 The suction has decreased by about 50%. The brush is still spinning. Any suggestions on what might be wrong?\015

Answers :

Check that there is nothing blocking the hose and that there are no obstructions around any of the filters, clean and replace filters too if possible. If you still find you have less than optimum suction , you may need to replace your motor. But it sounds like there may be a blockage or an air leakage somewhere in the unit.Good luck.
Repair Help & Product Troubleshooting for Hoover Windtunnel Supreme U5280-900 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The suction has decreased by about 50%. The brush

Check that there is nothing blocking the hose and that there are no obstructions around any of the filters, clean and replace filters too if possible. If you still find you have less than optimum suction , you may need to replace your motor. But it s ... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.

You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

Decreased suction was using to vaccuum carpet and suction decreased..nothing plugging hose....suction remain at unit canister and exhaust is fine....suggestions??

You might have a clog, to try and unclog the lines, you need to unplug the unit, and remove the bag compartment. Then take a shop vac using the hose attachment hold it into the attachment door where there is low suction and try to draw the clog out t ... Broan-NuTone CV353 Central Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.

Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

The brush does not turn but the belt seems very tight. There is also suction at the top of the hose but no suction at the brush head. I have removed ever pat that I can tell that comes off. Any suggestions?

DC07s have two drive ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.

Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?

Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I get plenty of suction at the hose, and none at the brushes. Also, the vacuum will not remain upright when I push it up. It appears that the part that switches the suction from the hose to the brush area is not engaged.

I looked up the problem where the machine would not stand upright, used that solution, and it worked. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No suction When I turn the vac on it sounds ok but there is no suction and the brushes don't turn. Alot of air does come out of the two exhaust vents and the brushes will turn manually.

Hey, how are you ?\015\012\015\012here are a ew things that could be causing you sorrow\015\012\015\0121.) Check your vacume to ensure that it isnt clogged anywhere\015\012\015\0122.) before your compressor and aft ... Hoover F6020-900 SteamVac Upright Vacuum

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.

Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.

Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Henry has great suction but as soon as I put the orange brush head on,there is no suction and the brush is not turning. Any ideas

Take apart and check all bearings ..belt more likely gone ... ... Numatic Henry Extra Canister Wet/Dry Vacuum

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?

As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

My manual says it is DC07, but it is pink and silver in colour. I have 2 problems, firstly the brush has stopped spinning, but belt appears intact. Secondly there are tiny holes in suction pipe near brush i.e. the little section of suction pipe at base of vacuum cleaner.

Hi there, \015\012The DC07 came out in a few different variations so the colour only indicates that yours has a hepa filter. The first problem can be caused by a few different things\015\0121. the brush roller bearings are worn or siexed. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush spin,good suction at hose, no suction at

Air passage from back of brush head, through the joint, and up to bag, may be blocked. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!

I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the "bag" compartment and when I look they are just all gathered in a clump in the bottom by the brush.

Hi.\015\012\015\012Remove the sole plate turn the 3 plastic screws to unlock & lift off.\015\012\015\012Now remove the blockages that have accumilated from the oppening of short clear hose.\015\012Check you can turn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.

First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

Its like the roller brush won't lower and it doesn't "engage" anymore. I posted this but input the wrong vacuum model ....not sure if that matters? I can vacuum and you still see footprints on the carpet. I have suction, just no brush action, yet the brush spins....

Sorry about that, I guess I have to post this as a solution in order for the pictures to display. Here's the entire solution on a similar problem that I've answered previously. Please let me know if you need help further diagnosing the machine, I ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan

I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

The machine will not suction - it will spray and spin the brushes but will not suction - the power is going to the machine, but it will not suction.

I had the same problem and after replacing the belt it started working great again. The belt was not cracked but it was stretched out which didn't let the brush spin at it's normal speed. The suction underneath wasn't the problem, it was the brush no ... Eureka Atlantis 2590A Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0603 seconds