Having problems with your Hoover Windtunnel Supreme U5280-900 Upright Vacuum ?

I need the part number for the wheel on the motor of this vacume u5280-940


Answers :

Go to this site for parts breakdown. to see the up close veiw, simply move your cursor onto the picture.


http://www.searspartsdirect.com/partsdirect/part-model/Hoover-Parts/Vacuum-Parts/Model-U5280-900/0517/0645000


good luck .
Repair Help & Product Troubleshooting for Hoover Windtunnel Supreme U5280-900 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need the part number for the wheel on the motor of this vacume u5280-940


Go to this site for parts breakdown. to see the up close veiw, simply move your cursor onto the picture. ... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

The pile adjustment wheel on my Sebo X4 has come off; I ordered a new wheel thinking that it would come with the PIN/AXLE but it doesnt. What do I need to order noe? I cant seem to find the pin as a spare part. Dp I need to order a servo motor? Many thanks Hannah


... Sebo X4 Bagged Upright Vacuum

Need replacement bushing part number for Kenmore, or motor?


... Kenmore Vacuums

I need a relay board for a Nutone CV 450 12.6 amp dual motor vacumn unit. Where can I locate one? Part #??? Unit will run by itself, then shut off. Unit wll not run at all. It has a mind of its own. Crossed a couple of wires on one of the relays and the unit runs smooth as silk. I assume its the relay, but can't locate part number.


Why not just replace the relay? Part number 1094117... ... Broan-NuTone CV450 Central Bagged Central System Vacuum

I need a synchronous motor replacement for an ice machine repair. The part number is; 50TYZ-E-1 120VAC 50/60Hz 1PH 3.5/4.1 RPM 3.5W Wuxi Dexan Micromotor Company Ltd. The ice maker is a Mr.Freeze model MIM-15, marketed by Maxi-matic, USA. I have accomplished an internet search for the part but have not received any responses.


I found the part you need on ebay! \015\012http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=330460832517#shId ... Vacuums

I need part number of front wheel assembly...


Part number for the wheels [you'll need to order two] 74818a-119n, the axle is part no. 71478 - available at sears 1-800-4myhome ... Eureka 4700A Maxima Bagless Upright Vacuum

My pump motor burnt out I need a part number for a replacement one. I have the little green bissel 1729-1. It is about 7 years old.


Good after,The item# for the pump motor is not listed in the user guide or anywhere else on Bissell's site: ... Bissell 1720-1 Little Green Wet/Dry Vacuum

NEED BETTER PIC AND MORE INFORMATION AND NUMBERSNEED PART NUMBER 4 DC07 MOTOR HOUSING THE CHEAP LITTLE CLIP ON RIGHT SIDE LOOKING AT THE FRONT NOT FROM BEHIND


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need the lower bearing part number or size for a hoover motor PN 43576203


I located a replacement bearing ... Vacuums

I need set of carbon brushes for motor i have found code number on carbon brush l83 f13a can,t seem to find supplyer for parts.


... Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum

I'm trying to find a part number for the motor on a 113296200c, craftsman wet/dry vacuum. Sears could only provide part number 09 113826404 for the model number 113296250c. I have found motors with the model number 826404 on ebay, however no one can confirm if this is compatible. Can anyone help me out here?


... Craftsman 17026 Wet/Dry Vacuum

I own a Eureka Optima 437 and one of the rear wheels are broken and cannot find parts for this. Where can I find parts for real wheel? I have a rear wheel that came off too. The wheel seems fine, but the plastic base that the wheel clicks onto on the underside of the vac seems to have cracked. I need a new plastic bottom. Any ideas?


Called Eureka Customer Service and ordered another part. They are mailing it to me free of charge!No more problem. ... Eureka 431A Optima Bagless Upright Vacuum

I need a service manual for an Electrolux C104A vaccuum. I know the part I need but don't have a part number. The part description is the hose connector at the beater attachment.


If you talking about the part that swivels it is called the elbow and the part number is 46861. ... Electrolux Guardian Bagged Canister Vacuum

Need part for stand of Hamilton Beach Scovill Model 44 Mixer. Part is locking rocker tab that hold mixer in place on stand or press to remove mixer head from stand. Don't need spring or pivot pin, just rocker tab. Don't have part number.


... Vacuums

I have a kenmore canister model number 116.2645083 I need a replacement motor. I was given 2 different numbers: 1. 4147248 2. AC92FAUX200 I can find the 2nd motor, but it doesnt have the 4 wires like the original one. Can you tell me if this is the right motor? Thanks Becky


Greetings from GoVcauum.com,\015\012\015\012Ok, so good news, I have looked up your model number for your Kenmore vacuum and found that your Kenhmore canister takes the motor ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!


On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

I just need the part number for my Guardian Electrolux model C134A i ran over the Hose and that was the part that broke. i need to compare prices so i can determine if it is cost effictive to change the switch or get a new hose


The part number for the hose is 47086.\015\012The best thing to do is contact the nearest Aerus Electrolux dealer. \015\012If it's just the switch or handle that broke, it will be more cost effective to have that replaced. If I remember ... Electrolux Guardian Bagged Canister Vacuum

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Does anyone know where I can get a motor bearing for the 3595 upright vacuum. Called Bissell and they say I have to be an authorized dealer to get "internal" parts and called their "authorozed dealer" and they told me they cannot get the part and I needed a new motor...ridiculous! Anyone put a bearing on these and if so where did you get it from?


Bought the whole motor assembly for mine, no bearing only part available. THis vacuum now headed for its third motor. " $45 dollars is still cheaper than a new vacuum". That's what I said the first time... ... Bissell CleanView 3596 Bagless Upright Vacuum

I need a part for a Shop-Vac model number 90LN650C. The part number is 7413100 inlet deflector


Http://www.vacshopusa.com/shop_vac1.htm ... Shop Vac Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Needs new motor have the part but cannot get into the part of the hoover where the motor goes


Have a look at www.dysonmedic.com. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Need reset button. Have part number. Can't find part online


May I direct your attention to one of the advertisers here at Fixya.com or www.repairclinic.com? ... Electrolux Centralux Vacuum

The female part of the catch which holds the lid to the accessories compartment closed has broken. This forms part of the handle to the vacuum cleaner.We've had the vacuum for less than a year but cant find the receipt so i think i will just have to pay for the parts. What is the part called that i need or the part number and where can i get it from. Many thanks


Even if you do not have the receipt you are still entitled to one or two year warranty.Since appliance sales are recorded after-sale by manufacturer, you need to contact the manufacturer to validate the warranty and get the replacement. ... Nilfisk Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1189 seconds