Having problems with your Hoover Windtunnel Vacuum Release Pedal 38434023 ?

How do I replace the release pedal on Hoover Windtunnel myself?

\015 Are there instructions on replacement once I have part?\015

Answers :

Repair Help & Product Troubleshooting for Hoover Windtunnel Vacuum Release Pedal 38434023

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

The handle release lever (Part N. 38434-021) on my Hoover WindTunnel upright vacuum (uses Y bags) broke. How do I install the replacement release lever (pedal) that I purchased?


You can buy Hoover Handle Release Lever 38434-021 at \015\012http://partsreadyonline.com/item.php?ItemID=798 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How do I replace the release pedal on Hoover Windtunnel myself?


... Hoover Windtunnel Vacuum Release Pedal 38434023

Hoover Handle Release Pedal Replacement--How is it possible?


If you look at the picture, the slots are right across from the drive wheels, you can see the slots in the picture. Use a flat blade screwdriver. ... Vacuums

How do you replace Hoover Handle Release Pedal on


The handle pedal is snapped in to the base, where it pivots.\015\012The pedal needs to be pried away fron the base, exposing the pivot pin to release it for removal. On your model, you will likelly have to remove the lower handle from the base ... Hoover Vacuums

Hoover windtunnel tilt mechanism won't remain locked in upright position or at any of the fixed angle positions - now any slight bump and the lock releases. Normally you must manually use the small foot pedal release on the left side as you face the vacuum from behind.


Hello, stanI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

In trying to repair foot pedal on my Hoover Windtunnel self propelled bagged vacuum, I got carried away and took apart most of the unit and I am still not able to get to the release..... I need help fixing the release lever AND then advise as to how to put the sweeper back together....Help!


This video should help you ... Hoover Vacuums

Replacing Main Body on Hoover Windtunnel Self Propelled


... Hoover Vacuums

I am trying to replace the lower hose valve assembly on my hoover windtunnel U5786. I have disassembled it to the point of loosening the old part, but can't get it to release.


... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

How to replace the handle release lever - Hoover U6446-900 WindTunnel Bagged Upright Vacuum


... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Replace hoover handle release pedal #38458022


... Vacuums

How to replace vacuum handle pedal release on hoover dm 5530


... Hoover Vacuums

Need to preplace handle release pedal - Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum


To remove the old pedal, simply insert a screwdriver along it's outside edge, and pry upward to pop it out. The new pedal, (#38434026) can be pushed into place with your fingers. Install it with the handle in the upright position. ... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

How do you replace the handle release lever on the hoover windtunnel 6425-900


The release lever is held in place by tabs molded into the base. You just need use a screwdriver or two to press the plastic tabs back and then push the release lever out. The new release lever can be just pushed into place and the plastic tab ... Vacuums

I have a Hoover Windtunnel Dual V. The vacuum and I did a tumble down stairs and the handle release pedal was broken. Is that something I can order a part for and have my husband put on? If so, where would I obtain the part? Thanks. Roxanna Kindler [email protected]


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=627747\015\012Generic problem for all Vacuums\015\012I have a Hoover Windtunnel\015\012Posted by ekindl ... Vacuums

Replace handle release pedal on a vax power 6


Http://support.vax.co.uk/power-2-upright ... Vacuums

Hoover WindTunnel Self Propelled Handle Release Lever broken


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t


... Hoover Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Replace motor hoover windtunnel - Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum


... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

The handle release pedal wasn't allowing the handle to lower. I took off the pedal and saw the spring load part was broken. What is this part and how to replace it? Bissell 3760-3 handle release


Our vacuum recently had an issue with it's motor, we had to borrow a neighbors a couple times while we were trying to figure out what to do. We decided to take it to a place that specializes in cleaning supplies and cleaning tools to see if they had ... Vacuums

How do I replace a hoover windtunnel belt - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Here is a link to the manual and to the belts you need.\015\012\015\012\011\011\011\011\011\011U6439-900 Manual \015\012\011\011\011\011\0 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to replace handle release pedal on dirt devil kinetix self propelled vacuum cleaner. I need to remove the broken pedal and replace it with the new one.


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

How to replace handle release pedal on dirt devil kinetix self propelled vacuum cleaner. I need to remove the broken pedal and replace it with the new one.


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0736 seconds