Having problems with your iRobot 5800 Scooba Vacuum ?

Replacing a scooba cliff sensor

\015 I need to replace my scoobas cliff sensors\015

Answers :

Repair Help & Product Troubleshooting for iRobot 5800 Scooba Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacing a scooba cliff sensor

... iRobot 5800 Scooba Vacuum

How do I replace the cliff sensors? I've taken

You're not supposed to be able to replace your own cliff sensors. They're recessed into the bumper. If you're out of warranty and determined to replace them, there are forums online where that information is laid out in detail. You can probably Googl ... iRobot Roomba 560 Robotic Vacuum

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.

... Sebo X4 Bagged Upright Vacuum

Have a Genie 2020L garage door opener. Door start to go down then stop and return. Tried cleaner old sensors. Same. Noticed red light on sensor 3blinks then off....repeat constantly. Replaced sensors - same issue. Reset unit...checked all wiring...no jams anywhere.... HELP PLEASE L:-)

... Vacuums

I have a wireless thermometer made by Viking (CE 0197). Have replaced the batteries of the remote sensor RF wireless. In the battery compartment there is button TX and a slide switch for position 1,2,3. Have replaced batteries pused button but no results of recording. Could you help me what to do to make the unit work again. Thank you

... Vacuums

How do i replace the squeegees on my scooba? - iRobot 5900 Scooba Robotic Wet/Dry Vacuum

... iRobot 5900 Scooba Robotic Wet/Dry Vacuum

How bumper and cliff sensor work in thish robot

... iRobot Roomba 560 Robotic Vacuum

I Have a Sharper Image EW400 In/Out door temp. clock. My remote sencor no longer works. How can I replace it? Only info is EW400, FCC ID: N92TTX302 and 08JAN0C Any help to get a remote sensor would be appreciative. Jim

... Vacuums

How to replace the IR bumper sensor board on a 500 series roomba

... iRobot Vacuums

Recieved this National Geographic Weather Station weather station for Christmas gift. I have had to replace the batteries in the outdoor sensor twice in two weeks??? Is this common? The outside temps have been below zero.

... Vacuums

How to replace bypass valve switch on windsor sensor vacum

... Windsor SR12 Sensor Bagged Upright Vacuum

Need to replace vacuum door - Windsor SR12 Sensor Bagged Upright Vacuum

I pried up the back of the cover holding the height adjustment wheel and was able to snap the cover axle with the cover installed into place. ... Windsor SR12 Sensor Bagged Upright Vacuum

Hi, my Roomba robot is spinning around. I cleaned it by disassembling wheels, gear compartment, etc.. Cliff sensors cleaned with compressed air. Briefly ran fine, but started to spin again. It's not under waranty anymore. Any suggestion please! Thanks, Olga

Usually this occurs when the front wheel is jammed or can't move freely, please verify if this is the case or not on your Roomba. Also, what model number of Roomba do you have? it should be located on the bottom of the unit on a label. ... iRobot Roomba 540 Vacuum

Roomba 560 is just over 1 year old and has worked well. Now it only moves 20 - 30 cm from point where it is put down and does not move across the room. I have cleaned the front wheel, and cliff sensors and have rest the software to default but no improvement. Suggestions please?

ARe you waiting for the error codes?\015\012There appears to be a problem with the bump sensors and they usually are going bad. Here is a site for the problem:\015\012 ... iRobot Roomba 560 Robotic Vacuum

Irobot Scooba model 33501 the check brush light immediately goes on and irobot does not work. I replaced the brush and it still will not run and the brush light remains on.

... iRobot 5900 Scooba Robotic Wet/Dry Vacuum

How do you dismantle a scooba and clean and replace parts

... iRobot Scooba 350 Robotic Vacuum

ERROR MESSAGE Roomba saying something like ''please inspect cliff sensors

When Roomba says "Please Inspect and Clean Roomba's Cliff Sensors" it means that Roomba 500 series sees a constant cliff.This can happen if Roomba was started on an uneven surface or got stuckon an obstacle during the cleaning cycle. Ex ... Roomba Robotic Floor Bagless Vacuum

ERROR MESSAGE Roomba saying something like ''please inspect cliff sensors

The "cliff sensors" are what help Roomba make sure that it doesn't tumble down stairs or over a cliff. You can see picture of their locations here:http://static.howstuffworks.com/gif/robotic-vacuum-16.jpgYou can try just blowing a bit of ... iRobot Roomba 560 Robotic Vacuum

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.

... Windsor SR12 Sensor Bagged Upright Vacuum

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A

This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

I have a sebo x1.1 automatic , the metal strip underneath has split and has half ripped off causing the brush sensor not to work and the jagged metal is scraching floor!!!can this metal strip be replaced and where can i get the part?

... Sebo Automatic X1 Bagged Upright Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

Need to replace belt on Windsor Sensor 12 vacuum

... Windsor SR12 Sensor Bagged Upright Vacuum

Replacing belt on brush gear on windosr sensor s15

... Windsor SR12 Sensor Bagged Upright Vacuum

Dirt finder sensor stopped working

I had the same problem with a hoover windtunnel 6200 - u5477-900. I removed the flexible hose from top of the plastic tube running vertically along the right side of the back of the vacuum. When I used a flashlight to look into the plastic tube, I ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0367 seconds