Having problems with your iRobot Roomba 4000 Bagless Robotic Vacuum ?

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


Answers :

It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593.
Repair Help & Product Troubleshooting for iRobot Roomba 4000 Bagless Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

The vacuum turns on but wont run smells like burning rubber I took the bottom off and the belts dont appear to be broken but the one connected to beater bar seems like it may be loose


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542493\015\012Generic problem for all Vacuums\015\012The vacuum turns on but\015\012Posted by mmetcalf on Apr 24 ... Vacuums

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!


... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a 5260D Baby Lock Serger, which I had tuned up a year ago. I haven't used it very much since. When I took it in, and again now, it sews fine for awhile, then starts slowing down until it is barely sewing, even with the foot all the way down. The hand wheel seems very tight. - it doesn't turn freely, but takes a some push, like it is resisting a bit. Any idea what could cause this slow down and the tight hand wheel? I appreciate any ideas. Thank you. Maura


Hi,Since you say that you didn't use it for many years then does it make noise?If so it need oiling on its parts.oil orifice and point of contact.Please do rate the solution if the issue is resolved or post a comme ... Vacuums

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?


The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

My brand new roomba ran fine the first time and for awhile today. Now it just turns in circles. It seems like one of the wheels doesn't turn. It gives 11 beeps.


CHECK CLOSELY WHAT STOPPING IT MOVE ... Roomba Robotic Floor Bagless Vacuum

I own a Eureka Optima 437 and one of the rear wheels are broken and cannot find parts for this. Where can I find parts for real wheel? I have a rear wheel that came off too. The wheel seems fine, but the plastic base that the wheel clicks onto on the underside of the vac seems to have cracked. I need a new plastic bottom. Any ideas?


Called Eureka Customer Service and ordered another part. They are mailing it to me free of charge!No more problem. ... Eureka 431A Optima Bagless Upright Vacuum

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it


My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don't even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.


Sorry, you feel like that. I have rentals and 6 windtunnel's (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.


Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust contai ... Vacuums

My Roomba Discovery 4210 seems to be dead. Specifically, with or without a battery, and whether on the charging station or plugged directly into the charging unit, I see no lights on the display whatsoever. This unit has a history of killing batteries, but now seems like it is completely dead. I understand that the batteries themselves contain fuses; is there some way to bypass the battery (for now) to verify whether the unit itself is completely dead? I should also note that this is the sec


Hello,I will advice you remove the batteries from your Roomba Discovery 4210, after removing the batteries, plug the Roomba Discovery 4210 directly with the charger to an AC outlet, see if charges, if it does, it means the batteries are d ... Vacuums

Clogged Hose 8 Year old Electrolux Centralux Vacume Cleaner has a clogged hose. Seems something is lodged in the middle of the hose - about half way down. I have tried a "plumbers snake" with no luck, except to clean out some "lint Balls" bot not the obstruction that seems to be like a "nail or stick".


Hi, this sounds like you have something stuck quite firmly in the hose!! If you use a good sturdy stick then you should be able to move the object without any damage to the hose. Check along the outside of the hose first just incase something has pus ... Electrolux Centralux Vacuum

My old bissell 3510 upright vacuum seems to have no suction into the bag...I replaced a broken belt several days ago, and now the vacuum picks up debris, but seems to just collect it behind a wheel..The bag does not "puff out" like it used to...How can I fix this??


... Bissell 3510 PowerPartner Upright Vacuum

Stopped working Was working fine then it smelled like burning rubber, not the belt I checked. It sounds like the motor wants to run then it just stopped but the light is on. What do you think, go by a new one?? This has been a great vacuum cleaner and I can not seem to find a Sharp anywere. Thanks for your time.


Well it could be the motor, if it is it would cost around $80 or so for a motor. May be better to buy new, thre are a number of good brands out there. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

When replacing the beater bar on the Oreck XL upright with a new bar, what way do the words "new" and "old" on the ends of the bar face?


Hello,I don't really understand your question, but I believe you are trying to replace the beater bar of your Oreck XL.... Follow the below instructions on how to replace your vacuum's beater bar:Turn your upright vacuum clean ... Vacuums

My Bissell Proheat left wheel cracked and I have a replacement wheel but can't figure out how to take it off. There seems to be no way to unscrew the bolt that is holding it on. Can you advise?


I believe it just pops straight out. Carefully pry it straight out with a screwdriver. It should snap back in ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Beater bar The beater bar will not work. I have changed the belt and there is a lot of suction from the hose. Just seems like the base is not turning on


You may have a bad switch, one part of it is not turning on the brush roll motor. It could also be the brush roll motor. ... Clarke CombiVac 12 Bagged Upright Vacuum

The pile adjustment wheel on my Sebo X4 has come off; I ordered a new wheel thinking that it would come with the PIN/AXLE but it doesnt. What do I need to order noe? I cant seem to find the pin as a spare part. Dp I need to order a servo motor? Many thanks Hannah


... Sebo X4 Bagged Upright Vacuum

I have a Hoover Savvy model U8174-900.. The beater brush only runs sometimes when I pull the unit backward. The handle switch seems OK but I cannot figure out why it is acting strange like this. Tilting the handle up or down does not seem to have an effect on this situaltion. Thanks for your help. Ron Simon


The Savvy has had its problems with the switch in the handle it will need to be replaced. Don the Vacuum Doctor Alb,N.M. ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Self propel will go foward, but will not reverse. Seems like handle is all the way extended.


My machine wont go forward or reverse. The handle wont move up or down but just a little which slightly moves the actuator piece. The switch wont disengage to the off position either. I have tightened the cable and loosened it also. No change. What a ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0961 seconds