Having problems with your iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum ?

It just goes in circles. It doesn't beep. Just goes in circles. I have had it about six months and have not had any problems with it.

Answers :

You can compare with the video on this website: www.eesolutions.ca. They also sell repair kits to fix the problem. It sounds like you have the IR Bump Sensor Error/ 9Beep Error.
Question . . . Have you cleaned the sensors and such?\012If so, Try holding the "power" button for 5 seconds to reload the firmware. \012Good Luck
Repair Help & Product Troubleshooting for iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It just goes in circles. It doesn't beep. Just goes in circles. I have had it about six months and have not had any problems with it.

You can compare with the video on this website: www.eesolutions.ca. They also sell repair kits to fix the problem. It sounds like you have the IR Bump Sensor Error/ 9Beep Error. ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

This is the 2nd shark mop that I've purchased. The first mop died after about 8 months. I know other people that this happened to. Is this going to be an ongoing problem? Does the steamer just quit working after 8 months?

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

How do I replace the hemp filter? Is there more than one? of course I've misplaced owners manuel, I've had it since July 2010, live where there are 3 indoor cats, I'm allergic to cat dander, for the first few months no problems with vacuum stirring up dander, however now, when vacuuming, my lungs start to close up. Definitely problem with the filtering system. Help! Today is 3.22.11, it's 11:24 am. Thank you.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover upright 2000w, HL2005 001 problems:the hoover made a pop sound & turned off. Tried leaving it for 30 mins as suggested in the manual but it still won turn on. Really cannot afford to buy a new 1 & would like to fix it. partner is an electrician so if we have some guidance as to what the problem may be i am confident we can fix it. the hoover is only 18 months old so not very old at all.

... Vacuums

Help Hi I have had my irobot roomba model 4000 now for 3 months now, I just LOVE it sooo much. I have used it everyday since I got it. But now it is not working. I cleaned it all out I even sprayed it with that air spray can. What happens is, It starts to go then it acts like there is something in the way and stops then goes the other way, then goes off. What is wrong? Please help!!!

I had the same kind of problem with my model 400 today...after starting it and having it go in a circle for 30 seconds or so it would finally run into something and then back up a few inches, turn, then go forward a few inches, then back up a few inc ... iRobot Roomba 4210 Bagless Robotic Vacuum

My princess 3 feels like its getting awfully hot on top it doesnt shut off yet whats the problem before it really becomes a problem?

... Filter Queen Majestic Canister Vacuum

I have the same problem as steve967 The dyson dc16 is fully charged, runs well for 5-10 seconds and shuts down. I wait for a second or 2 and it runs again for 5-10 seconds. This will continue for numerous cycles, until I am finished cleaning. I have cleaned all the filters, and the power is good, The system will just not stay on. It is just over 2 years old. A friend of mine had the same problem with his Dyson DC16 after just a couple of months and has replaced his Dyson with a Black N De

Dear Michael_Stad,I am going to sound like a broken record but here is my same answer to another person with the same problem.I have I had the same problem with my Dyson DC16, where it only runs for a few\015\012seconds at a t ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

I purchased one of your fans and installed in the summer, no problem and I am satisfied. After seven months one of the energy efficient bulbs has stopped working. I am no tree hugger, but energy bulbs good for seven years sorta made sense, but for seven months? I got in touch with the bulb people but they dumped it on you. Fan 20169-380, 14 watt bulb-0924235. The fan was purchased at home depot in Willow Grove PA. My name is Mark T. King, 1012 Lansing Street, Philadelphia Pa. 19111. e-mail-markt

... Vacuums

My Eureka central vacuum of almost 10 years, has a reoccurring problem, of a defective relay on the pc board. The problems is usuallly the motor will not turn off. The pc board has been replace 8 times, of which 3 times were with in the last 4 months.

Are you taking the machine in to someone? or is this a self diagnosis?? \012\012What I mean with those questions is, sometimes it isn't the PC board that is causing the problem. Sometimes it is something else. Even the people that you are ... Eureka CV1804B Bagless Central System Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?

Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

No suction I have a similar problem - volta vortex bagless vacuum will not ****. Worked for 1 job then quit sucking, I have had the heads replaced, then the barrel - 2 months later same problem. I push the power lever to max - 10 seconds later it turns itself down and doesn't work properly. I am over it, now looking for refund

Hi there SmartAlec from NelsonVacuums.com.au here. The problem is going to be the filter. THis kind of vacuum basically replaces the bag with a simple filter and the vacuum ... Vacuums

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b

... Vacuums

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and

Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


You probably have a bad motor bearing. I don't know if the motor is available now or, these older Fantom's are obsolete along with most of their parts. ... Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

ZB2803, charging light on, then it goes off but there is no power. What is the problem

... Electrolux Zb2803 Unirapido Rechargeable Stick Vacuum Cleaner, Fresh Yellow

I have had a Hoover Linx cordless stick vac for several months. Even after charging the battery the vacuum will not run at all. What are potentially the problems and how do I get it fixed.

... Hoover Platinum LiNX Cordless Stick Vacuum

Just goes in a small circle, no lights to indicate problem

Actually it very well can be bad or dirty sensor that you can clean with rubbing alcohol and cotton swab. If cleaning the sensor doesn't help, then it may be a firmware or electronical problem like faulty resistor or capacitor ... iRobot Roomba 530 Robotic Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Suction Problem I took my unit to my work and used it, when I returned home it wouldn't suck up anything. I took the recovery take out and it has inward suction. Shouldn't that be outward, so it goes into the tank? It also blows out of the bottom by the brushes. I check the filter in the bottom and that is fine. Is it possible that it is somehow reversed the direction of the air flow (rotor running backwards)? I am perplexed. What am I missing?

There is a stand pipe seal where the bucket sits on, and if it isn't there or out of place could cause a suction problem like you said yours is doing. In the picture it is #10. The motor seal may have gone bad and is leaking # 15.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

I recently ( approx. 2-3 months ago ) purchased a dirt devil. Now it is not picking up properly. When I push vacuum forward it picks dirt up a little bit, when I pull it back all the dirt falls out of the bottom. I replaced the filter today and it has not solved my problem. I dont know where my warranty is. Can you please help me?

Hi sounds like your line is stopped up somewhere , check ur suction an make sure your brushes are spinning, if they are try a wire clothes hanger to the hose at the bottom hose to dislodge anything that mite be stuck ... Dirt Devil Vacuums


It might be clogged. ... Hoover Elite U5349-900 Upright Vacuum

I bought a used vacuum seal machine (hobart model ht-120) it does excellent vacuum but it doesnt seal correctly all the time. it seems like there is something wrong with the valve that activates the bar that goes up and makes pressure and heats the bag for complete sealing. The heating is perfect but what is not working is what make the bar go up and down.

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0547 seconds