Having problems with your iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum ?

Irobot roomba 500 goes in a tight circle than stays in one place.


Answers :

Repair Help & Product Troubleshooting for iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Irobot roomba 500 goes in a tight circle than stays in one place.


... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Roomba 560 goes in circles. appears lost - iRobot Roomba 560 Robotic Vacuum


I had the same problem. This is the 9-beep error. It goes in backwards circles. Pretty much a bad component in your Roomba, makes it think that it is constantly in collision mode. This makes it go backwards in circles. I fixed mine using this ... iRobot Roomba 560 Robotic Vacuum

My irobot goes in circles - iRobot Roomba 530 Robotic Vacuum


I had the same problem. I had the circle dance and looked around for a fix. Finally found a site that sends out do it yourself kits. I was apprehensive because I'm not that good at fixing things. I tried it out because it is a lot cheaper then ... iRobot Roomba 530 Robotic Vacuum

The roomba or I robot will upon pressing the start button go around in circles, than starts to goin one direction, than stops and goes in a circle. The unit is clean and the unit reset. Bill


Is the front bumper **** in? ... Roomba Vacuums

I have a iRobot Roomba 5545, when I put it on, it starts like all circling outwards, but as soon as it touch's an object it goes into a reverse cycle stuttering motion in oposite direction. I hav


Please download your instruction manual from www.irobot.com according a your model, And see the troubleshooting section , and proceed according with the indication for fix it. Many thing can be wrong. Sensors, Motor, Software, loose wires, or maybe s ... Vacuums

540 Roomba goes in tight circles left and right after backing off charging base - stops and give oh-oh signal and 9 beeps - I have taken off bumper and cleaned sensors etc - blown out with air and still have same issue - unit will also not find or go back onto charging base - any suggestions /


... iRobot Roomba 540 Vacuum

It just goes around in a circle - iRobot Roomba 530 Robotic Vacuum


Hi. One of the bumper IR LED is at fauly. You can replace the IR LED HERE ... iRobot Roomba 530 Robotic Vacuum

My roomba scheduler irobot only goes in circles. how do i fix it


... iRobot Roomba Scheduler 4230 Bagless Robotic Vacuum

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Goes in erratic circles then stops - iRobot Roomba 560 Robotic Vacuum


\015\012Your bump sensors are malfunctioning... The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. I'd recommend them. ... iRobot Roomba 560 Robotic Vacuum

Goes in circles - iRobot Roomba 530 Robotic Vacuum


\015\012\015\012\015\012Your bump sensors are malfunctioning.. I had the same problem. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. ... iRobot Roomba 530 Robotic Vacuum

It only spins in one place then stops - iRobot Roomba 560 Robotic Vacuum


As said, if it beeps 9 times after stopping, than this is known issue and if your bumper moves freely, you might be facing a sensor fault caused by poor quality of components.Here is a ... iRobot Roomba 560 Robotic Vacuum

My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz


Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum

Roomba goes around in circles


I had the same issue too. I fixed mine using a repair kit from eesolutions.ca ... iRobot Roomba 530 Robotic Vacuum

My irobot roomba 4110 is going in circles


Check all the wheels to make sure that they are ok. Check the sensors on the bottom and make sure they are all clean. ... Vacuums

Roomba goes in a circle moves about 5 inches and then turns in a circle again. It won't dock or go any farther than a few inches before turning in a circle again. The roomba has been cleaned inside and out. All hair and debri as been taken out of the wheels and brushes. i opened the case and cleared all the debri and i dusted the sensors in the front. Not sure what to do now.


... iRobot Roomba 550 Vacuum

IRobot Roomba going in circle and quits


You need to turn roomba over, leave the battery in, push the wheels at the same time 15 times. after that, push the front bumper about 15 times. then turn on roomba and press clean. ... iRobot Roomba 4210 Bagless Robotic Vacuum

Roomba starts out in a circle goes wider and wider then all at once goes in circles.


It's the circle dance bug. Pretty much Roomba thinks there is something in front of it ALL the time, causing it to only go backwards. You can fix it by buying a repair kit online ... iRobot Roomba 560 Robotic Vacuum

Roomba turns in circles going one direction and then another but can not go forward in a straight line. Aftter a few moments of going in circles, it cuts off and says inspect and clean roomba's wheels. We have done that 5 times and to no avail.


... iRobot Roomba 530 Robotic Vacuum

Roomba wont stop going in circles,code 9 comes up, cleaned front caster wheel to no avail. 500 series roomba. called company said we need a new one, if this is the best we can get out of a roomba they are junk.


\015\012\015\012Your bump sensors are malfunctioning. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great.. ... iRobot Roomba 560 Robotic Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

I bought Roomba 560 and love it. It didn?t come with a lighthouse so I bought one on Ebay. When I put the batteries in it the green light on top flashes 5 or 6 time very quick and then stops, it doesn?t flash after that. When placed in front of the Roomba in either mode, virtual wall or lighthouse it doesn?t direct the Roomba. The question is, is there a process to marry the two units together or do you think the lighthouse is defective? Thank you Gary


... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

The Roomba goes around in circles. If it


Sounds like the 9-beep error. Google "roomba repair kit" to get it fixed. ... Roomba Robotic Floor Bagless Vacuum

My roomba pro elite just goes around in a circle. how can I fix this? I have cleaned the roomba as thoroughly as I can. Could it be a recently changed wheel tread?


The infrared sensor circuit has failed, u will need to have it repaired ... Roomba Pro Elite Bagless Robotic Vacuum

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.


... Panasonic Kenmore Canister Vacuum Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0678 seconds