Having problems with your iRobot Roomba 530 Robotic Vacuum ?

The clean light on the Roomba 520 doesn't quit blinking even when it has been docked for hours, i checked all the plugs and i also pushed the spot button for 10 seconds. it is a a slow continual blink as if it is recharging continually. what is the problem.

Answers :

Sounds like you didn't remove the batteries protective tape. If this isn't a new roomba, your problem may be the charging cycle. For a brief video of what to do click the link below.

Repair Help & Product Troubleshooting for iRobot Roomba 530 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The clean light on the Roomba 520 doesn't quit blinking even when it has been docked for hours, i checked all the plugs and i also pushed the spot button for 10 seconds. it is a a slow continual blink as if it is recharging continually. what is the problem.

Sounds like you didn't remove the batteries protective tape. If this isn't a new roomba, your problem may be the charging cycle. For a brief video of what to do click the link below.http://irobot-homesupport-en-eu.custhelp.com/app/answers ... iRobot Roomba 530 Robotic Vacuum

I have a Bissell Proheat 2x Model 9200. The solution goes directly through to the carpet. The tank empties extremely fast even when I am not pushing the button. I have also noticed that I have soap spots on the carpet when pushing the cleaner forward. These spots are not even associated with the cleaning mechanism. I have inspected the cap on the tank, but it seems to be OK. Any suggestions?

Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9200 Upright Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.

The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

Roomba 560, the small red light above the schedule button will not reset and the roomba will not run. The problem started when I the roomba sat dead for 12 hours. I tried the spot dock reset trick with no luck. The clock and sunday light stay let also.

This work ok for me ihave a 560 thanks ... iRobot Roomba 560 Robotic Vacuum

Dyson dc25 schecking continuity on reset switch its a 91 series 2 amp switch but whether i have button pushed or not a get continuity shouldn't this break when button is pushed

... Dyson DC25 All Floors Bagless Upright Vacuum

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?

Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

My swan steam generator iron s15040n is showing a push button when it is turned on. im pushing the button but it continues to say push and keeps beeping. the iron wont turn on at all. please help!!!!! thanks

... Vacuums

Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.

Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum

My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have the Oreck Sanapathic DMS2000 Handheld Steam Vacuum, but no steam comes out when I push the button. I hear the motor, is there any buttons I am missing or any help on how to make it work, been plugged in for 5 min now. Held button down for 2... nothing. Just a drip of water.

ORECK DMS2000 No Steam First, tested tank and filter flow together using suction via plastic tubing. Worked freely Second, removed pump and disconnected hoses and terminals [watch location,three terminals on pump, two plugs] ... Oreck Sanapathic DMS2000 Handheld Steam Vacuum

While using my mop yesterday, it stopped letting steam come out. Tonight I plugged it up again and you could hear it trying to steam. I push the button in to release the square frame and it pushed out a burst of steam and pushed the head off. Put it back together and it still will not let steam out. No matter how much water is in it.

\012Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Ste ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Stops I had my iRobot Roomba 530 in storage for 8 months. I didn't remove the battery. When I plugged it in to recharge it, it did recharge after several resets but it would not dock itself once it had finished. It kept trying but I had to turn it off and manually dock it but it now won't recharge at all. It is totally dead. What is the problem.

I had the same problem when I renovated my kitchen. With boxes of stuff everywhere it was impossible to use Roomba. When I tried to use it again a few months later, it would stop after only a few minutes work. I had to buy a new battery which cost i ... iRobot Roomba 530 Robotic Vacuum

I want to recharge my Philips PET741 D/05 portable DVD Player. But when I push the plug into the charging point on the side of the player,at one point, as the plug goes in, there is a quick flash of red - but no more. The red charging light does not light up, and the player does not charge. The plug cannot be held at the point where the sudden momentary flash takes place

1.With the AC power unit plugged in to the wall plug into your dvd player and wiggle it a little bit and see if the light goes on or off. If so the the power port is bad. \015\0122.Try a different wall outlet to see if it helps.\015\0123.Ensure there ... Philips Vacuums

Dyson DC23 Vacuum shut off and came on. Thought it was a problem at the electrical outlet as when moving plug it would come on again. Seen canister was full, emptied it and cyclone was quite plugged up so poked out the dirt. Had dog hairs in it as well as some ashes I had just vacuumed. Plugged unit in again and pressed switch. Will not come on. Tried another outlet. Is there a reset button somewhere or could the ashes have seized the motor. What can I try besides taking it to a repair sho

... Dyson DC23 Bagless Canister Cyclonic Vacuum

The beater bar motor doenst work when i push the bar button the bar button doesnt light up like power button how can i test bar motor or bar switch or what is the common problem wiyh this model I have 2 that dont work the same way

If it do not work ...and you already are on the second one that behaved in the same way it may be a problem with the power in your place and the cause it may be the main fuse...Im not sure where is located in this model but it has to be near the powe ... Vacuums

Water will not come out when i push on trigger button. So water does not come out. I have taken it apart and cleaned it. The problem seems to be in the triggerI push on the handle to release the water.

Order the part from bissel see if that fixes sound like you know what wrong just need get part number from bissell.Could be some kinda pump also thats bad not pushing out the water.I got bissle heated one black it only problem the seals r ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson 24. I just bought a new Dyson ball 24 and the brush won't turn on, I tried to follow instruction and push the red button to reset it also next to the power button but doesn't do anything. Any suggestion.? Thanks Sam


Shark s3325 stopped working while steaming; thinking the unit had ran out of water I allowed unit to cool before refilling, however unit over flowed with only 700ml water added. When I plugged unit back into outlet it would not turn on (red light was not on) but I hear a click upon plugging in unit, when turning unit power button on and when turning on the handle switch. Please advise how to resolve this problem.

... Euro-Pro S3325 Handheld Steam Vacuum

My TDK Clock Radio for iPhone & iPod (ADS-6P) freezes when I use the power button for the radio feature or try to set the alarm using the radio. Also using the ipod or iphone dock doesn't work. I have no idea what has caused the issue. Turning it off and on again doesn't help - it is still completely frozen and unresponsive to buttons pushed on the applicance one it has frozen. Can you help? I was given this item as a gift so I do not have the reciept.

... Vacuums

My shark vx3 vacumn has stopped running... i tried recharging it, but still no luck... i then put a new battery pack on it and tried recharging, still it won't run... the charge light, (green) is on, the three red lights come on and flash when i push the on button...what should i do next?? this unit is about 6 months old... help!!

... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

When I plugged in my Riccar Vacuum cleaner - it made a pop sound. The breaker had not been moved - there was no smoke or apparent damage. I tried to depress the restart button and nothing happens. Is there a technique about pushing the restart button. Please advise.

Check the cord where it goes into the machine on back. most likely blew out at machine ... Riccar 8955 Upright Vacuum

Same problems - power nozzle motor does not work after cleaning the brush and pressing the reset button. Also the handle button which turns on the nozzle does not light up (my wife thought it lit up before).

Hello,\015\012\015\012This is a pretty common problem on the Guardian, and it's usually caused by 1 of two things. Both are pretty simple fixes. The first thing you should try is simply eliminating the wand assemblies from the vacuum c ... Electrolux Guardian Bagged Canister Vacuum

I recently purchased a Sunbeam Artista EM5900 model coffee machine. I plugged it in and pressed the 'Power' button only to find the power go out. I understand this is short circuiting, so I went and turned the power back on. I then moved the machine to a different powerpoint and plugged it in - the same problem happened and I have tried it countless times on various other powerpoints. Help please?

Try it in a different part of the house. If it works then you have too many things running in the kitchen.\015\012If it still blows a breaker then it is shorted out and needs to be returned. ... Vacuums

Hoover Max Extract Dual V Carpet Washer sprayer on hose leaks and button on hose that controls spray sticks causing continuous spray. Solution?

... Vacuums

I have a Kirby Sentria and when I push the "on" spot with my foot it comes on then when I take my foot off - it goes off! What is the problem?

Your switch has worn out. you'll need to replace it cause it wont be long before it wont turn on at all. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0946 seconds