Having problems with your iRobot Roomba 530 Robotic Vacuum ?

The motor driving the brushes does not start or function in any way. It has been thoroughly cleaned and the bearings look good and the brushes rotate freely when the mach is off.

Answers :

There are two conditions that cause the brushes not to spin. One ia a cold solder joint on the paddle board connector of the Cleaning Head Assembly and the other end that connects to the brush motor may also suffer From the same condition. Here are some of my photos to reference\015\012
Repair Help & Product Troubleshooting for iRobot Roomba 530 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The motor driving the brushes does not start or function in any way. It has been thoroughly cleaned and the bearings look good and the brushes rotate freely when the mach is off.

There are two conditions that cause the brushes not to spin. One ia a cold solder joint on the paddle board connector of the Cleaning Head Assembly and the other end that connects to the brush motor may also suffer From the same condition. Here ... iRobot Roomba 530 Robotic Vacuum

My roomba 560 has brushes that spin one rotation then stop then you hear a click and they rotate one rotation stop over and over. I took compleatly appart cleaned, lubed, and inspected all looked good?

Here's the solution to this problem...\015\012\015\012Remove the rollers and run the Roomba and see if the problem goes away. If so, here is the solution to the problem...\015\012\015\012Each roller has a little yellow cap on ... iRobot Roomba 560 Robotic Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab

(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate

If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch

... Hoover Vacuums

My dyson dc 07 brush will not rotate. I have cleaned all hair and debris from around the brush and no change. I can not even figure out how to look and see if the belt is still attached. Suggestions?

DC07s are not easy to check the belt on, in fact depending on which exact model you have there are probably two belts.\015\012One connects the output of the motor to the clutch mechanism (one end of which has the control knob that ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz

Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum

Is it possible to take the Hoover Brush Block Assembly F7220-900 #48437029 apart so that I can thoroughly clean inside the block? It looks like it could, but I don't want to break it by trying.

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Every thing clean & sucking well except wont pickup off floor. brush in good condition &rotating. any answers would help.

This is hard to answer without see it in person. Check and make sure there is no broken pieces on the bottom where you could loose suction. Also make sure you have the machine set correctly for either bare floors or carpet. If it is on set on carpet ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The beater brush on my Bissell 6596 is not moving freely. Is there a lubricant to free up the spinning end piece or a way to remove and clean this thoroughly? I burned up another belt trying to fix it.

You can try petroleum jelly. It works good. Just don't get any near where the belt loops around. ... Bissell 6596 Bagless Upright Vacuum

I have a Kenmore Progressive Inteleclean Upright vacuum cleaner (with Bag) . It has good suction only through the hose now and none through the bottom for cleaning carpets. and, there is a noise like it has a suction leak. the brush is rotating.

Theres a little bendable neck that hose with suction plugs into. Thats the one thats clogged. You will have to fish it out by taking off the roller and clearing the clog. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Bad smell after using my windtunnel for a couple of minutes i noticed an odd smell. i turned it over and checked, the belts are fine but i cleaned out the hair anyway. after doing that the self propel seems to struggle and it is hard to push. when i look through the window on the top i can see the brush spinning freely but then when i push it, it slows down dramatically and then picks up again. the suction is fine. what do you recommend?

It may be the roller bearings? ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

The powerhead brushes no longer rotate. The interior is clean and the belt is intact and in good shape. Is there something that I can check or do I need to replace the powerhead

Make sure elecricity is getting to the power head. if power is getting to it, you need to replace the little motor ... Vacuums

Hoover Mach 6 stopped running and won't start up. Cleaned the brushes(roll freely) and checked for a clog but couldn't find any.

Ya okay how do you get to the motor. Then when you get to the motor are you soppose to guess what is wrong with it by just looking at it.. What kind of solution did you give this person? I'd say not a very good one. ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move

There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)

I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

Cleaning brushes wont rotate

I understand how important the brushes are when cleaning. You may want to the check the pump belt for breakage for the brush belt and pump belt work in conjunction with the pump. If you're still experiencing difficulty, you may want t ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.

If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?

Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0797 seconds