Having problems with your iRobot Roomba 550 Vacuum ?

Troubleshooting My says to clean brushes but they are clean. Whats going on?


Answers :

Repair Help & Product Troubleshooting for iRobot Roomba 550 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Troubleshooting My says to clean brushes but they are clean. Whats going on?


... iRobot Roomba 550 Vacuum

My Irobot Roomba keeps saying that I need to clean Roombas brushes. I have cleaned the brushes...they are spotless. Still the Roomba will go for 2 minutes and shut itself off stating once again to clean the brushes. What up?


Perform the troubleshooting found at the iRobot website: http://tinyurl.com/nh5c8a (I promise that really does go to the right site.) That troubleshooting will enable you to determine exac ... iRobot Roomba 510 Bagless Vacuum

Roomba keeps saying clean brushes yet are clean!


Make sure you take off the little cap at the end (the one that spins -- just grab it and pull it straight off) and clean under it too. The rest of the brush may look perfectly clean but what happens is that hair gets stuck under spinning cap and, li ... iRobot Roomba 530 Robotic Vacuum

My roomba will not go forward. it will turn in a circle for a few seconds then shut off with the red light flashing. i cleaned the brushes and the wheels. i dont know whats wrong with it.


... iRobot Roomba 530 Robotic Vacuum

My iRobot Roomba runs for 5 minutes, then it say error 2 open brushes clean brushes, which i did, then 5 minutes later it start again saying error 2 clean brushes.


... iRobot Vacuums

Brushes are clean, but Roomba stops and says clean brushes


I decided to take it apart and see if I could fix it because even if something inside went "SPROING" and I couldn't get it back together, it wouldn't be any worse than it was already. \015\012\015\012FIrst, remove the dust bin part and t ... iRobot Roomba 4210 Bagless Robotic Vacuum

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.


Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

My roomba tells me to clean the brushes and stops; however beforehand, it goes around going "click, click, click". The brushes have been cleaned - all hair removed, etc. but the clicking noise persists. What is going on? It's only a few months old!


... iRobot Roomba Discovery SE Bagless Robotic Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

My Roomba runs for a while and says error 2 to clean the brushes. This happens with cleaned brushes. And I have followed the instructoins. i have got a brand new set of brushes also. When inserting them the same problem continues. The floor is clean.


Remove the two round rings.....this has worked for me like a charm since! So glad to have the Roomba back up and running! ... iRobot Roomba 560 Robotic Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!


Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Roomba keeps saying clean brushes yet are clean!


Remove the Yellow connectors on the end of the brushes and clean around the pin well. If there is too much there, the roomba thinks there is something stuck and goes into clear mode (as if there is a chord stuck). ... iRobot Roomba 560 Robotic Vacuum

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

My Roomba 560 is making a clunking noise when it is on and it keeps stopping saying that I need to clean the brushes. I've thoroughly cleaned the brushes and I've cleaned lint from other small crevices but I'm still getting the error. Any suggestions?


I'm having the same problem with my 560 after a day of use. For me, it's caused by the little yellow spacer that's clipped onto each side of the bristly brush. When the brush assembly is closed, it wedges rather tightly next to that yellow spacer on ... iRobot Roomba 560 Robotic Vacuum

My Roomba says to clean the brushes when the brushes are already clean. Is there something to take apart to check? I have already taken the brushes out. I don't know the model number, I think it's the 500 series, black and silver.


Turn the unit upside down and remove the bottom pan should be 4 or 5 screws depending on the model. next remove the 4 screws that hold the brush cartridge and pull the whole brush assembly out.using a can of compressed air cle ... Roomba 3005 Pro Robotic Vacuum

Hi my dyson is not sucking up very well when i put it on its side and switch it on the brushes are not going round when i put the white dail to on at the bottom the brushes go round but it makes a terrible noise i have cleaned the brushes checked the soleplate is on correct and taken the clear hose off and checked for splits the suction is there when i have been checking these things hope you can help thx


Hi there,Sorry to hear you're experiencing a problem with your cleaner. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US). We can run through some checks over the phone and provide you with the assistance you nee ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Our Roomba 530 stops after few minutes saying clean the brush ,even after brushes are cleaned.


FIrst, remove the dust bin part and the brushes. Then, there are four\015\012screws on the bottom gray panel which have to be removed first in order\015\012to get to the gears which hold the brushes. I did not remove the little\015\012sweeper brush o ... iRobot Roomba 530 Robotic Vacuum

Roomba discovery My roomba comes off the charger and will go about a minute and a half. Then it will stop and beep once. i checked roombas sight and they said that the brushed need to be cleaned. I cleaned the brushes 6 times. It still does the same thing. I bought it from you in November of 2007. Should I bring it back to your service department?


Greetings doreen f,\015\012\015\012The roomba unit carries a one year manufacturers warranty, so you should be able to bring it into your local Best Buy™ store and have them try to repair it. \015\012\015\012I hope this ... Roomba Robotic Floor Bagless Vacuum

It clicks as it is going and stops after about 30 seconds. Two beeps. I have tried cleaning brushes and have pretty much taken the whole thing apart, cleaned the motor, the brushes everything. Still doing to same thing, when this has worked before.


It clunks because the gears are damaged. You will need to replace the CHM. If you have the red cleaning head module, chm, replace it with the green chm. ... Roomba Robotic Floor Bagless Vacuum

Runs for awhile then says error 2 please remove and clean roomba's brushes i do then runs for awhile and says same thing no dirt on brushes?


I had the same problem. You must clean this parts and inside this parts: Remove hair with cleaning toolRemove Roomba's brush bearingsClean Roomba's brush bearings with cleaning tool ... iRobot Roomba 560 Robotic Vacuum

IRobot Roomba 560 Thumping, Says Clean Brushes, No Dirt in Cup


... iRobot Roomba 560 Robotic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)...... when I leave the rubber one in, it doesn't pick up & then finally stops & says REMOVED BRUSHES..... I have cleaned every nook & cranny of this thing... inside & out. I finally found that if this one brush is left off.... it works great & has for 2 weeks??? What could be the problem?


Hi,\015\012First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On t ... iRobot Roomba 560 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0795 seconds