Having problems with your iRobot Roomba 560 Robotic Vacuum ?

ERROR MESSAGE Roomba saying something like ''please inspect cliff sensors

Answers :

The "cliff sensors" are what help Roomba make sure that it doesn't tumble down stairs or over a cliff. You can see picture of their locations here:
You can try just blowing a bit of compressed air on the lenses of those sensor since they can malfunction if dust builds up on them. If the sensors have gone bad, you can find new ones at places like
www.roboticvacparts.com or at this link

Repair Help & Product Troubleshooting for iRobot Roomba 560 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

ERROR MESSAGE Roomba saying something like ''please inspect cliff sensors

The "cliff sensors" are what help Roomba make sure that it doesn't tumble down stairs or over a cliff. You can see picture of their locations here:http://static.howstuffworks.com/gif/robotic-vacuum-16.jpgYou can try just blowing a bit of ... iRobot Roomba 560 Robotic Vacuum

ERROR MESSAGE Roomba saying something like ''please inspect cliff sensors

When Roomba says "Please Inspect and Clean Roomba's Cliff Sensors" it means that Roomba 500 series sees a constant cliff.This can happen if Roomba was started on an uneven surface or got stuckon an obstacle during the cleaning cycle. Ex ... Roomba Robotic Floor Bagless Vacuum

Roomba 550 keeps saying please remove and clean roomba's brushes. I have done so and keep getting error message.

Pull both brush rollers out.pull off funny looking yellow ends and clean out hair ect. ... iRobot Roomba 530 Robotic Vacuum

Runs for awhile then says error 2 please remove and clean roomba's brushes i do then runs for awhile and says same thing no dirt on brushes?

I had the same problem. You must clean this parts and inside this parts: Remove hair with cleaning toolRemove Roomba's brush bearingsClean Roomba's brush bearings with cleaning tool ... iRobot Roomba 560 Robotic Vacuum

We have a jvc nx pn10 ipod dock. Every time we turn the power on it says "Hello" briefly then P-ERROR. Nothing will remove this message. Can you please help?

(This question should not be in the Vacuum section - the device in question is a Clock/Radio/iPod dock) I had just this problem but could find no solution on the Net. JVC could provide only a PDF of the manual, which nowhere mentions P-ERROR. So, w ... Vacuums

Have roomba 550 that keeps on turning around ending up with an error. cleaned the sensors and brushes but no result. when i undo its bottom and put it back it runs until it bumps into something

... iRobot Roomba 550 Vacuum

Roomba 560 is just over 1 year old and has worked well. Now it only moves 20 - 30 cm from point where it is put down and does not move across the room. I have cleaned the front wheel, and cliff sensors and have rest the software to default but no improvement. Suggestions please?

ARe you waiting for the error codes?\015\012There appears to be a problem with the bump sensors and they usually are going bad. Here is a site for the problem:\015\012 ... iRobot Roomba 560 Robotic Vacuum

Help Hi I have had my irobot roomba model 4000 now for 3 months now, I just LOVE it sooo much. I have used it everyday since I got it. But now it is not working. I cleaned it all out I even sprayed it with that air spray can. What happens is, It starts to go then it acts like there is something in the way and stops then goes the other way, then goes off. What is wrong? Please help!!!

I had the same kind of problem with my model 400 today...after starting it and having it go in a circle for 30 seconds or so it would finally run into something and then back up a few inches, turn, then go forward a few inches, then back up a few inc ... iRobot Roomba 4210 Bagless Robotic Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

Hi, my Roomba robot is spinning around. I cleaned it by disassembling wheels, gear compartment, etc.. Cliff sensors cleaned with compressed air. Briefly ran fine, but started to spin again. It's not under waranty anymore. Any suggestion please! Thanks, Olga

Usually this occurs when the front wheel is jammed or can't move freely, please verify if this is the case or not on your Roomba. Also, what model number of Roomba do you have? it should be located on the bottom of the unit on a label. ... iRobot Roomba 540 Vacuum

I kept getting an error message from i-Roomba on charging .. Charging Error 3. I just bought a new battery and it has the same error message.

... Roomba Robotic Floor Bagless Vacuum

My iRobot Roomba runs for 5 minutes, then it say error 2 open brushes clean brushes, which i did, then 5 minutes later it start again saying error 2 clean brushes.

... iRobot Vacuums

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet

I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

Roomba Schedular I have a Roomba Scheduler and it has worked great until recently. Suddenly it quit working. When it is charging the power light goes from red to green as it should, showing it is ready to use. When we turn it on to use, it will only go on for a few seconds then it shuts off like it is out of power. It is like it isn't really charged. Is there something I can try to make it work?

Let it charge for a full 24, or even 48 hours, regardless of the green light. If it still dies you probably need a new battery.. or worse. ... Roomba Robotic Floor Bagless Vacuum

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)

I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

Battery charge I just purchased a new battery pack insert for my Roomba, Replacement was a breeze and it now works great. My question is; The last battery I bought ( not from you) was a full cased roomba battery pack that didn't last a year. Roomba says leave the r Roomba charging all the time so it's ready when you need it, and that's nice but I feel that leaving it charging like that it will kill the battery faster as it is always warm to the touch. These battery's should last at least 5

Dave you are correct. You should never over-charge anything like a Roomba, Cel Phone, etc. That will kill a bettery very quickly. ... Roomba Robotic Floor Bagless Vacuum

Irobot roomba 530 charging error 5

Click this link for helphttp://uksupport.irobot.com/app/answers/detail/a_id/883/related/1/?cc=uk ... iRobot Roomba 530 Robotic Vacuum

My Roomba 770 will not start. When I push "clean," "spot," or "dock," I get one beep. There is no voice error code like with other errors. I am still able to drive it around manually with the remote c

The beep code means that it cannot verify all of its wheels are on the floor. Turn the unit upside down and make sure there is nothing stuck to the wheels or sticking between the wheels and chassis ... Vacuums

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!

Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Roomba turns in circles going one direction and then another but can not go forward in a straight line. Aftter a few moments of going in circles, it cuts off and says inspect and clean roomba's wheels. We have done that 5 times and to no avail.

... iRobot Roomba 530 Robotic Vacuum

Hi, I have a Casio fx-115s scientific calculator which I've had for around 25 years. I am unable to use the bracket function and have lost the instructions. Could you please give any advice to save me having to buy a new calculator? I'm not sure how to use the brackets, whenever I press the ( ) buttons, it shows -E- on the screen which I'm presuming is an error message. Please help.

You should be able to use parentheses in the same order in which you would write the arithmetic expression. For example, 4*(3.5-1.5)= should give you 8. Without the parentheses, this would 12.5.Essentially, the left parenthesis comes imme ... Vacuums

Keeps saying error 2 - clean brushes - iRobot Roomba 560 Robotic Vacuum

... iRobot Roomba 560 Robotic Vacuum

I have a Milan scientific calculator and i am trying to calculate standard deviation. The answer that i get for sum of values and no of data are negative and when i try to calculate standard deviation i get a ma error message. Please help me. Thank you

... Vacuums

Error message says to clean brushes, even after it has been cleaned

Your gears are jammed and you cant see them to clean them. You will need to disassemble it and flip the brush deck over to clean it out. ... iRobot Roomba 550 Vacuum

I have an older Oreck XL that has worked great. The belt recently broke and I reinstalled a new one but now there's a rattling noise like something is loose and a burning smell. I've cleaned it as well as I could but still nothing. Help please!

When you turn it on, is the brush roll spinning? (Check carefully, as lifting the unit from the floor exposes a brushroll that should be spinning at a high RPM.)\015\012\015\012Did you get the brush roll properly seated in the slots? Does ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0502 seconds