Having problems with your iRobot Roomba 560 Robotic Vacuum ?

How do I replace the cliff sensors? I've taken

\015 How do I replace the cliff sensors? I've taken the robot apart but cannot find how to get to the sensors.\015

Answers :

You're not supposed to be able to replace your own cliff sensors. They're recessed into the bumper. If you're out of warranty and determined to replace them, there are forums online where that information is laid out in detail. You can probably Google them.
Repair Help & Product Troubleshooting for iRobot Roomba 560 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I replace the cliff sensors? I've taken

You're not supposed to be able to replace your own cliff sensors. They're recessed into the bumper. If you're out of warranty and determined to replace them, there are forums online where that information is laid out in detail. You can probably Googl ... iRobot Roomba 560 Robotic Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.

It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

My 2001 miele stopped working Black cannister. I believe cleaning ladies overheated it as the bag was very full and the vac felt warm to touch. I replaced bag and let cool down but it will not start. This has happened before and the vac store said they replaced the cord because it tends to go when it over heats. I have not taken in for and estimate but I fugure it will be at least $150 to repair. Is the another option.

... Miele S548 Bagged Canister Vacuum

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.

... Sebo X4 Bagged Upright Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Replacing a scooba cliff sensor

... iRobot 5800 Scooba Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.

... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

I have a Kirby Heritage II which normally works amazingly well, but it's not playing at all nicely today - and of course we have apartment inspections tomorrow. *dies* The belt broke today (as did the replacement belt, which I'd bought at the same time, so apparently the rubber was old), so I went over to Stark's to get some new ones - but it still won't cooperate. I've taken the head apart and put it back together several times, to be sure that everything is properly seated, but it's just not

... Kirby Heritage II Vacuum

DC28 Clutch DC 28 Clutch made knocking noise after about 1 hr of use. Tried to take it apart and see it it had an obstruction but burned up the belt and damaged clutch. Yes, I know I should heave taken to the dealer or warranty service but thought it was something simple. Nothing inside is simple on a Dyson! Can the clutch be replaced and from what vendor?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

New battery!, roomba runs for 5 - 10 seconds, stops, starts running, stops, runs, stops, then beeps and low battery flashes. Have taken battery out, held start button 20 seconds, replaced battery and directly connect to charger, 72 hours min., still same problem.

... iRobot Roomba Discovery SE Bagless Robotic Vacuum

The digital readout on my Redmon brand digital small animal pet scale will not "zero out." When turned on, the weight displays a weight from the memory, which is what the scale should do, but it's then supposed to zero out so you can weigh the animal. I've put new batteries in, and also taken them for a while (up to an hour), then replaced the batteries, and turned the scale on. This has not worked. Any ideas?

... Vacuums

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil

Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

Need to replace belt on a Kenmore Model: 116 37312690 vacuum. Have taken torn belt off. Is there a diagram available? I have lost owner's manual.

Instructions:\015\012\015\012\015\012 ... Vacuums

The roller on my Dyson DC24 quit rolling. I've taken out the brush, cleaned it, replaced it, locked it and push the reset button but it still isn't rolling. Help!!! I've only had this for about two months.

... Dyson Ball DC24 Bagless Upright Vacuum

Brush roller not spinning. belt, spindle okay. roller taken out and cleaned, no thread. replaced but no dice. ???

Use only BISSELL Style 10 Replacement Belts (#32074) in your BISSELL PowerForce Bagless.\015\012\015\012Unplug cleaner from electrical outlet.\015\012With Rotating Floor Brush removed from vacuum clean ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Need to replace impeller fan on Classic III. Half the blades are broken off. I can't figure out how to remove it. I have taken cover off.

... Kirby Vacuums

Replace motor taken apart putting back together dont know what coulr wire goes to which from the heating ellement

Green is always ground. white or gray is always neutral. and black, red always hot. without know what make,model machine your working on this is best info i can give. ... Vacuums

My Hoover SteamVac F5915-900 will not pick up water. I've taken the resavor off several times trying to make sure nothing is under it's lid and replaced it as instructed. I don't know wh


Eureka Optima 431 Green Model - Can't find brushroll replacement

... Eureka 431A Optima Bagless Upright Vacuum

Foot operated release "spring" is broken. Replaceable?

... Bissell 3590 CleanView Bagless Upright Vacuum

How to replace geared belt on Hoover Savvy U8171

Tom, This one is tricky. First get the belt on the geared motor pully, and then insert the roller through it. You will have to roll the brush toward the body of the vac to have enough room. Patience is the best on this model. ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0644 seconds