Having problems with your iRobot Roomba 560 Robotic Vacuum ?

560 backs out of charging base then only turns in right circles

\015 Roomba 560 backs out of charging base then only turns in right circles, and eventually the red light flashes and tone beeps about 10 times\015

Answers :

Yes, this is known issue and if your bumper moves freely, you might be \015\012facing a sensor fault caused by poor quality of components.
Here is a\015\012 guide to fix it
http://www.schneordesign.com/Avi/irobot/roomba_mod2.htm
Have\015\012 fun\015\012 \015\012 \015\012 \015\012
Avi
Its probably 9 beeps rather than ten... its likely to be a sensor malfunctioning. It might be a cliff sensor, the bump switch, or wheel-drop (left, right, or caster). Try cleaning the sensors and vacuuming things out as a first step.
Repair Help & Product Troubleshooting for iRobot Roomba 560 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

560 backs out of charging base then only turns in right circles


Yes, this is known issue and if your bumper moves freely, you might be \015\012facing a sensor fault caused by poor quality of components.Here is a\015\012 guide to fix ithttp://www.schneordesign.com/Avi/irobot/roomba_mod2.htmHave\ ... iRobot Roomba 560 Robotic Vacuum

540 Roomba goes in tight circles left and right after backing off charging base - stops and give oh-oh signal and 9 beeps - I have taken off bumper and cleaned sensors etc - blown out with air and still have same issue - unit will also not find or go back onto charging base - any suggestions /


... iRobot Roomba 540 Vacuum

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My dyson hand held shuts down after about 30 seconds, It turns back on again, but it does this over and over again, even after being fully charged with caontainer emptied. Its almost like an overheating thing, but different since it starts right back. It is annoying.


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

The machine backs out of the dock, then proceeds to turn in circles, stop and then start turning in circles again. I have cleaned all of the sensor areas and made sure the bumpers were not stuck against the machine. Any ideas


... iRobot Roomba 560 Robotic Vacuum

I installed a new battery in my Roomba 540. It charges and runs directly with power cord but will not charge on dock. When I push the dock button, it acts like it "sees" the dock and approaches it and even slides on, but then gets back off again and just keeps going back and forth until I turn it off.


... Roomba Robotic Floor Bagless Vacuum

Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a


Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o


... Kenmore 25512/ 25513 Progressive Canister Vacuum

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron


The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

My Prosine 2.0 display panel displays Panel Fault: Memory error and the display error as well as all LEDs are off. The unit looks as if it has no power to it. I reset (power off.power on) the Prosine and all LEDs on the display (except for the back lit display) turn on for about 3 seconds then all go off again. I am able to use 120v RV Resort power and all 120v equip works. The Coach batteries do not charge and were low. I charged the Coach batteries with an external charger. The charge works ye


... Vacuums

Needle rubbing I have a singer pro finish and recently I broke a needle and the lower looper also busted clean off. I ordered the lower looper and replaced the broken one and changed both the needles. Now when I turn the hand wheel and the lower looper moves to the left and the needles descend they pass in front of the looper but when the needles begin to move up and the looper moves back to the right the needles bend back and go behind the looper. Help! Thank You!


... Singer 14CG754.CS Pro Finish Industrial Commercial-Grade Serger

I vacuumed up a AA battery. I quickly shut off the vacuum. When I turned it back on the sweeper bar was not turning. the base does not look level. How do I adjust this. The belt is not broken.


Remove the rim piece at vacuum inlet and press the roller back into its end slots. Should straighten it out. Good luck ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to


When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums

I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy


Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums

Hi: My DC14 (not animal version) has 3 major cracks that have pretty much killed the thing. There are three 'columns' that run down from the handle to the base. From the back, the left one has either the intake or outflow for the canister and the right one has the reverse. The middle one is where the base of the extension hose and cord is mounted. On all three the plastic has cracked at about the point where the bottom of the canister meets the permafilter. The vacuum is useless now and


I'd suggest using an epoxy cement (3M makes really good stuff) The epoxy comes in 2 separate tubes or bottles. Each alone will do nothing, but when combined become incredibly strong. Use care when using since on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Roomba 560 has started to run in small steps as if it constantly meets an obstacle and turns around in a very small circle. It advances slightly, backs slightly and turns and then does this again and again.


Sounds like your Roomba has the Circle Dance Error. Here is the fix for the Circle Dance. ... iRobot Roomba 560 Robotic Vacuum

This is a roomba 560. First started acting crazy, ''even ''singing'' on the base. No no power at all, no clean botton light at all, the base turns green when you put it in there like charging ... The baterry measures little over 14V. I tried to reset it but no change...


Something is blocking the battery current and preventing the Roomba from running.\015\012\015\012Low voltage contacts can be blocked by thin films formed by condensible organic outgassing in the home environmental (That's the yellowy haze ... iRobot Roomba 560 Robotic Vacuum

I have had a dyson vaccuum cleaner for three months and it does a great job, but the red on/off power switch won't stay on now. As soon as you press it down to turn on, it comes right back up and turns off. What can be done?


Hi its Darran at Dyson.Call our Helpline on 1866MYDYSON and one of our advisors will be able to arrange for this to be reparied. As your machine in only 3 months old, this should be covered by the warranty. Kind regardsD ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I want to brush the pile up on my carpet do I need a special attachment to do this??. I have shampood it and it still seems a bit flat. When I shampood no water/foam filled up in the front tray???I am sure I had attached everything correctly. The only thing I can think of is when I attach the brush and tray to the front of the machine, do I turn the handle back to the right way up, or do I leave it upside down, this is the one that picks up the belt.


Here's my online guide for using the Kirby shampooer....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I took the trap(or whatever it's called)off the bottom right corner to check for an obstruction as my hose was collapsing when using the attachments. Put it back on(perhaps wrong)and now when the vacuum is turned on, dust blows out the front and there is NO suction! HELP!


Now you have a dyson leaf blower! not funny huh? Ok, just slow down and recheck your connections. Sounds like the motor is running backwards or you are hook up to the discharge. ck for baffles that block off the vacuum to the roller part when at ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

IRobot only turns in 360 degree circles, it is fully charged and cleaned. How does it get fixed?


\015\012\015\012\015\012\015\012\015\012Your bump sensors are malfunctioning. I had the same problem. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. I'd recommend... ... iRobot Roomba 530 Robotic Vacuum

Bought clearance item Sunday just found out the brush bar was motorized it turms only when i move the vacum back and fourth it should turn on its own right ? I have very little suction from the bottom the hose works though


This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem. That is why moving it back and forth makes it go on.\015\012\015\012I have finally fixed my sister's d ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna


... Singer Vacuums

Not picking up as well as it use to seems to be blowing back out some lint and debris. Also when i turn it on after a second it goes to a different noise as if a hose is not connected right or something?


There seems to be a bad connection at one of the hoses or filters.\015\012Possibly a broken,or loose hose.Put some baking powder on the floor,\015\012and try vacumming it up,to see where the white smoke is escaping.\015\012Good luck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0778 seconds