Having problems with your iRobot Roomba 560 Robotic Vacuum ?

Throughly cleaned roomba of dog hair, including taking off gears. After putting back together the brushes no longer move. Any suggestions


Answers :

Try turning manually about 20 turns and re try, might have to do a couple of times, make sure no hair caught under yellow tips
Repair Help & Product Troubleshooting for iRobot Roomba 560 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Throughly cleaned roomba of dog hair, including taking off gears. After putting back together the brushes no longer move. Any suggestions


Try turning manually about 20 turns and re try, might have to do a couple of times, make sure no hair caught under yellow tips ... iRobot Roomba 560 Robotic Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

I was vacuuming, and ran over an area rug with those tassle things on the end. the brush immediately stopped spinning. so i turned the vacuum off and un-tangled the brush. after replacing the brush and putting the assembly back together, the brush no longer rotates.


Did you smell something burning? You probably melted/broke the drive belt. ... Dyson Ball DC24 Bagless Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?


The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

I replaced the belt on my bissell model number 3576-2, but when i put it back together, the brushes wont move...the belt tries to move, but the rubber just burns..


Something is binding ... i dont know what ... you will have to remove all parts and reinstall again. Make sure the bearings spin on the brush when it is out ... remove all hair and string.\015\012\015\012good luck ... im sure it is some ... Bissell 6595 Lift Off Bagless Upright Vacuum

LittleGreen Machine Pro turbo brush put back together


Here is the web site with the parts breakdown.\015\012http://www.marbeck.com/carpetcleaner_parts_bissell.html ... Bissell Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

Thanks! Awesome tip to get into the gear box. My roomba would start up but would move very sluggishly. Looked up the beep code and it was the brushes. Brushes are cleaned regularly so it was something internal. Did your solution of getting into & cleaning the gear box and viola! He's back!


... Roomba Robotic Floor Bagless Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

The brush roller on my vacuum will not move. I've cleaned it, checked the belt, but when I put the roller back it, it will not move...almost like it is in a locked position. Everything has been done correctly from the book yet, it still does not move. Any help PLEASE?


... Electrolux EL8502 Versatility Bagless Upright Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Had infamous extra part once I put my steam cleaner back together


Steve, The o-ring goes inside the turbine assembly on the metal shaft. ... Hoover F7220900 SteamVac V2 Upright Vacuum

Have eureka 9734 replaced belt, put back together,brush rotates well but vacuum is not picking up anything, no suction.


It sounds like the machine is clogged. Check the port behind the belt and any and all hoses for obstructions and remove. ... Vacuums

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.


Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I just purchased a Dirt Devil machine on Monday, I finally got it put together today and the brushes are not moving, dust is swirling around but no brush movement, I have changed all the nap settings, nothing, I am having company tomorrow and I threw my other vacuum cleaner away, HELP ME. Thank you.


Sounds like you may not have the belt attached or it is broke. ... Dirt Devil Vacuums

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I bought a fantom vacuum on HSN about 9 years ago.Whan it was delivered the first one was broken so they sent a second one.tThat one also was cracked on covering for brush. I called and they told me they were no longer available,so I kept that one,since it would cost me shipping to return.The back right side wheel evenually cracked and fell off.I was able to put it back on and it would stay for a few weeks or so.It now has a large piece of plastic that has broken off the wheel where the bolt fit


... Vacuums

I removed the revolving brush to remove a jammed piece of debris I had picked up and after putting brush back, it no longer revolves


Reattach your belt properly and the beater will function.\015\012\015\012Thanks for your interest in FixYa.com ... Vacuums

I have an old Riccar N2000 (biege) the belt connects to a little ''tension'' piece or ''guide'', not to the brush directly as in newer models. When moving-- this piece is somehow no longer there? Where can I get another one? Went to shop in town, they want $60 + labor to put the ''newer'' one piece brush thing in.....


... Vacuums

What causes these things to become unbearably loud? We've cleaned evey filter on the machine, pulled every speck of hair and lint off the brushes, changed the belt, no clogs anywhere. I've totally (and I mean totally, down to the brushes on the motor!) torn this thing down and put it back together with no difference. Also have a Eureka bagless, and after minimal use, and almost anal retentive maintance, it does the same thing,to stinkin loud. Wish one would **** up the other to save a trip to th


A clog in the hose or dirt inlet by the brush roll will cause the motor to sound loud. But so will a bad motor bearing, or motor fan, in which case you would have to replace the motor. ... Bissell Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0657 seconds