Having problems with your iRobot Roomba 560 Robotic Vacuum ?

Roomba 560 is just over 1 year old and has worked well. Now it only moves 20 - 30 cm from point where it is put down and does not move across the room. I have cleaned the front wheel, and cliff sensors and have rest the software to default but no improvement. Suggestions please?

Answers :

ARe you waiting for the error codes?
\015\012There appears to be a problem with the bump sensors and they usually are going bad. Here is a site for the problem:
\015\012here is another one:
Check to see that the eye that senses the walls and furniture is not covered with dust and debris. This could cause the machine to move slightly then stop. Are the wheels turning on the machine when it stops or is it just stopping?
Repair Help & Product Troubleshooting for iRobot Roomba 560 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roomba 560 is just over 1 year old and has worked well. Now it only moves 20 - 30 cm from point where it is put down and does not move across the room. I have cleaned the front wheel, and cliff sensors and have rest the software to default but no improvement. Suggestions please?

ARe you waiting for the error codes?\015\012There appears to be a problem with the bump sensors and they usually are going bad. Here is a site for the problem:\015\012 ... iRobot Roomba 560 Robotic Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

Hi, my Roomba robot is spinning around. I cleaned it by disassembling wheels, gear compartment, etc.. Cliff sensors cleaned with compressed air. Briefly ran fine, but started to spin again. It's not under waranty anymore. Any suggestion please! Thanks, Olga

Usually this occurs when the front wheel is jammed or can't move freely, please verify if this is the case or not on your Roomba. Also, what model number of Roomba do you have? it should be located on the bottom of the unit on a label. ... iRobot Roomba 540 Vacuum

Roomba goes in a circle moves about 5 inches and then turns in a circle again. It won't dock or go any farther than a few inches before turning in a circle again. The roomba has been cleaned inside and out. All hair and debri as been taken out of the wheels and brushes. i opened the case and cleared all the debri and i dusted the sensors in the front. Not sure what to do now.

... iRobot Roomba 550 Vacuum

My Windsor Sensor XP12 says the bag is full when it's not. I have removed the hose, brush, and filter and cleaned everything. I can put a bag on without the cover and it works great. However, when I add the bag to the front cover and close the latch the right way, it does not work. I'm thinking that the cover is not seating the bag correctly over the hole, but I can't figure out how to fix it. Any suggestions?

... Windsor SR12 Sensor Bagged Upright Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.

It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

Front wheel problem

I would send it to protechrobotics. they will test all your components and let you know what needs to be done. if the repair is more than it's worth--they will help you out too.http://www.protechrobotics.com/ ... iRobot Roomba 4210 Bagless Robotic Vacuum

My roomba won't go forward it just spins in a circle and will go backwards. I have already tried cleaning it out and cleaning the front bumper sensors.

This is the Circle-Dance Error. I had the same problem. I just ordered a repair kit from EESolutions.ca and did the fix myself. Works like new to this day. ... iRobot Roomba 530 Robotic Vacuum

How to clean the unit? The clear suction part in the front gets filled with fibers and other **** and I don't know how to get it cleaned out without breaking it. Any suggestions?

I use a knife blade or nail file (metal ones you get at any drug store) to get the fibers out. With new carpets it's a mess - have to clean the bottom of the unit as well as the brushes and up inside the area where the brushes are housed. Otherwise ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Cleaning! To clean the cyclonic cone Dyson say to use can-air? that may be ok for computers but not to blow out the dirt and dust from the cone in question. Someone else here suggested to use a real compressor! Well dahhh I knew that! Should I do the blowing in the living room? or may be in the bathroom? Seriously what I need is an assy. drawing to take it apart and washing it Any ideas where I can get one? Thank you John

Hi, we realy love our Dyson, but get frustrated when it gets clogged with pet fur (2 cats and 2 dogs). This takes a little effort but what we ended up doing was taking the vacuum apart into its major components and alternately blowing it out, filter ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The problem is that the cleaner is heavy to use and does not pull itself forward as it should. It has been back to the supplier 3 times but they have not fixed the problem. The LED's on the front flicker and I think it may be a problem with the sensor. If you have any info. on how the sensor works and where it is located it would be useful as well as any other suggestions to fix the problem please.

If it heavy then do some muscle work and body building ... Vacuums

Hi my beater bars will not turn anymore, i have tried to reset it cleaned the bars removed and cleaned the front wheel, but still they will not turn.Any help would be appreciated

Belt has probably broke in the power head ... Vacuums

We understand that your problem is: I currently own and use on a regular basis the Kenmore Progressive upright bagged vacuum. Model number 116.35923500. The headlight flickers and the intelliclean light stays red. Ive tried cleaning the intelliclean sensors, changed the bag, and cleaned off the agitator. Is this a power issue? Should I take it to the store? Any suggestions would be greatly appreciated

Welcome to fixya\012\012Hello\012\012 \012\012I have a solution for this ... Kenmore Progressive 35922 Bagged Upright Vacuum

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher

If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

I have a Hoover Mach 3 Cyclonic bagless upright vacuum. It works for a room or two and then it just shuts off. Then it won't turn back on for hours. Any suggestions on how to make it stop doing this? The canister is cleaned out.

This vacuum is very picky about air flow clean the filters and that should do it ... Vacuums

Irobot roomba 500 series not picking up dirt. Filter is clean, brushes clear, small wheel at front is clear. Seems to be operating fine other than not picking up dirt.

Pull roller brushes out .pull off funny looking yellow ends clean hair ect. ... iRobot Roomba 560 Robotic Vacuum

Kenmore InteliClean 116.35923502 Two, I believe unrelated, problems. 1) The InteliClean sensor lights stay amber and red even when the machine is in the upright position and the suction line is disconnected from the cleaner head. 2) There is a lot of vibration and noise in the agitator roller housing. I picked a little hair out of the roller brushes but other than that they were clean. Thank you for any suggestion you might offer.

I had the same problem with the amber inteliclean light continually on. I found the problem to be in the plastic housing that connects the suction hose to the back of the upright section. You have to remove three screws and gently pull ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

We have this vacuum and its not sucking enough. its sucking at about 50% capacity. we vacuumed an entire room and when we opened it up, there was nothing in the dirt holder. we have cleaned all filters and tubes...any suggestions?

A common probem with vacuums that are equipped with an attachment switch is the switch isn't all the way in it's normal position. Our Bissell has a yellow dial that switches from normal to attachment mode and will only work at 1/2 its power if the s ... Bissell 6594 PowerForce Bagless Upright Vacuum

I want to clean fluff from underneath the transparent front panel of my Bissell 11 7901. I have removed the screws from the bottom of the panel, but it remains firmly in place. I do not want to apply apply forceful leverage in case there is something else that needs to be done before the panel will come off. Any suggestions, please? Peter

I just did this one myself, You've done most of the hard work already.Be sure your holding tank is out and not in the way.Double check the down front screws are still out since you sent in you question. Now tweak the front section (the business end) ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The roomba 560 keeps going in circles after it hits an object. Or it will keep hitting the object repeatly until you pick it up and move it. I have cleaned the sensors and wheels and it still does not work properly. Thank you.

... iRobot Roomba 560 Robotic Vacuum

Panasonic canaster vacumn cleaner model MC-9647C only runs a few seconds and shuts off, after a rest starts then stops after a few seconds. I changed bags and cleaned the filter...any suggestions? Thanks, Phil

... Panasonic Vacuums

Bin isn't filling, won't pickup and brushes won't spin for the second time. Last time iRobot had to replace both wheel modules. Any suggestions? I clean it every time I use it!

Wheel modules? It's more likely to be the cleaning head module. Clean your brushes exactly as the manual describes-- particularly the yellow bearings. Run the Roomba on a hard floor without the dustbin. Does the brush turn? If not, call support again ... iRobot 560 Roomba Vacuuming Robot, Black and Silver Vacuum

Scooba The "i'm Stuck" with 2 beeps keeps coming on I cleaned the front wheel and it made no difference. What else can I check?

Ensure that the front caster can spin freely, pivot, and rotate. Remove the caster by pulling it out and clear any dirt. Reinsert the wheel and lightly push the wheel up and down ... iRobot 5800 Scooba Vacuum

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.

Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

540 Roomba goes in tight circles left and right after backing off charging base - stops and give oh-oh signal and 9 beeps - I have taken off bumper and cleaned sensors etc - blown out with air and still have same issue - unit will also not find or go back onto charging base - any suggestions /

... iRobot Roomba 540 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0789 seconds