Having problems with your iRobot Roomba 560 Robotic Vacuum ?

Roomba spins around in 1 place. it then stops and beeps 9 times. it seems perfectly clean sensors are cleaned etc.


Answers :

\015\012\015\012Your bump sensors are malfunctioning. The best thing to do is order a repair kit.. I ordered mine from EESolutions.ca and it worked great.
Repair Help & Product Troubleshooting for iRobot Roomba 560 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roomba spins around in 1 place. it then stops and beeps 9 times. it seems perfectly clean sensors are cleaned etc.


\015\012\015\012Your bump sensors are malfunctioning. The best thing to do is order a repair kit.. I ordered mine from EESolutions.ca and it worked great. ... iRobot Roomba 560 Robotic Vacuum

Hi, my Roomba robot is spinning around. I cleaned it by disassembling wheels, gear compartment, etc.. Cliff sensors cleaned with compressed air. Briefly ran fine, but started to spin again. It's not under waranty anymore. Any suggestion please! Thanks, Olga


Usually this occurs when the front wheel is jammed or can't move freely, please verify if this is the case or not on your Roomba. Also, what model number of Roomba do you have? it should be located on the bottom of the unit on a label. ... iRobot Roomba 540 Vacuum

My iRobot Roomba 560 starts spinning sporadically during the cleaning, and after over 3 minutes it complete stops and beeps 9 times. It is necessary to turn it on until it decides to work properly, and keep waiting for the next time the same failure will occur. I tried to reset it, and I have all the dust removed including from the bumper and sensors.


It's the bumper. Blow it out with compressed air and clean the cliff sensors. If you still get the 9-beep error, call support. ... iRobot Roomba 560 Robotic Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Irobot roomb will not work. I've discharged the battery and recharged for 16 hours. Acts like it is going to come on but sort od revs up and then gives a series of 6 or 7 or 8 beeps.. Goes so fast I cant count them. I've cleaned everything. Aftertyring a couple to Times, it seems that the battery discharges... Clean light goes red. Please help... i need this thing to work!,,


... iRobot Roomba 550 Vacuum

It seems to be blowing dirt around not suking but when removing the attachment to clean stairs etc the pipe works fine have washed filteR ? SLIM UPRIGHT DC ALLERGY 18. Have cleaned out filter emptied cylinder taken any bits of cotton or hairs from brushes..........


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet


I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Agitator unit on Kenmore Progressive 116.25915503 won't spin. I have cleaned out all hair and string wrapped around it. Belt is good. It seems to spin on one side but stuck on the other. Could string be caught somewhere?


Pry the end caps off the brush bar, you will find hair and string wrapped up tight in the end. the bearing may also be shot, you can try and oil it up a bit to keep it spinning.\012\012<!-- from fixya rte --> ... Kenmore Vacuums

Roomba 560 beeps 9 times; we've cleaned the


Yes, this is known issue and if your bumper moves freely, you might be facing a sensor fault caused by poor quality of components.Here is a guide to fix ithttp://www.schneordesign.com/Avi/irobot/roomba_mod2.htmHave fun\015\012 ... iRobot Roomba 560 Robotic Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks


This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

535 series - just put in new battery - does not work - just spins around in circles and tries to back up - then beeps nine times (bumper?) Won't dock.


Hey\015\012\015\012Please look for other same problem posted here ;-)\015\012\015\012You are probably facing a bumper sensor issue.Try to clean the bumper first and if this goes on, either call ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

540 Roomba goes in tight circles left and right after backing off charging base - stops and give oh-oh signal and 9 beeps - I have taken off bumper and cleaned sensors etc - blown out with air and still have same issue - unit will also not find or go back onto charging base - any suggestions /


... iRobot Roomba 540 Vacuum

Hoover Savvy The red light for the dirt finder is on when pushing forward and the green light is on when pulling it back. This happens all the time. It's like the dirt finder sensor isn't working right. It seems to be picking up good and we keep the filter clean.


Does this happen at both Dirt Finder Sensitivity settings? ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Spins around in a circle and then beeps 9 times and shuts off


Yes, this is known issue and if your bumper moves freely, you might be \015\012facing a sensor fault caused by poor quality of components.Here is a\015\012 guide to fix ithttp://www.schneordesign.com/Avi/irobot/roomba_mod2.htmHave\ ... iRobot Roomba 550 Vacuum

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.


I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My roomba backs away from docking station then starts to go then stops and spin left then stops and spins right after a few times stops and beeps many beeps. What is the problem


It sounds like the 9-beep error. You can fix it by buying a repair kit from www.eesolutions.ca. I fixed mine in about an hour and a half. ... iRobot Roomba 530 Robotic Vacuum

I have 2 #560 roombas. They both beep 9 times. I have replaced batteries and also cleaned the bumpers several times. Why does it beep 9 times?


Try this linkhttp://uksupport.irobot.com/app/answers/detail/a_id/880/?cc=uk ... iRobot Roomba 560 Robotic Vacuum

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.


You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene


... Vacuums

Two weeks ago, my 4150 roomba stopped during running and sounds "ehh". every time i hit the clean button it sounds "ehh" and doe'snt work. at the first time it did it ,i have cleaned the sensors then it start moving forward and backward until it stopped . from now on it only sounds "ehh".


EHH sound:-------\015\012Cliff sensors are dirty or need repair.Try cleaning the sensors and check.If still the same problem then the sensors needs to be rechecked and its connections has to be replaced.\015\012You can try this opt ... iRobot 4150 Roomba Vacuum

My 4150 goes around in circles. It is about 2 years old and I clean it every time I use it which is several times a week. I use canned air to clean it but still does not correct the problem. Just started today.


I have had this problem, I called the company. Blow out all the sensors, I used an electric tire pump with a small pointy attachment to blow out all the dirt. You will be surprised to see the dirt fly. ... iRobot Roomba Red 4100 Bagless Robotic Vacuum

Def no choked probs, as I check and clean filters regularly, but when switched on there seems to be a short whineing sound before returning to normal, and def wont lift fluff etc., just runs over it, although ther seems to be a fair amount of suction. It does clean but not properly


Hi, this is Jack at Dyson.\015\012\015\012You should be able to resolve your problem by following these simple steps: http://www.dy ... Dyson Ball DC24 Bagless Upright Vacuum

5 yr. old Miele s514 Turbo plus's power nozzle brush seems to disengage temporarily, stopping the spin. Then it seems to re-seat itself after a few seconds, then starts spinning OK. I keep the nozzle brush very clean, so there is no hair or yucky stuff to cause it to jam. Please help.


I had a White Pearl with same problem. As I moved the hose/wand the brush motor would start stop. Find out where the circuit opens up by holding one part and moving the part that connects to it - 1) where the hose plugs into the cleaner, 2) the swi ... Miele S514 Solaris Turbo Plus Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1164 seconds