Having problems with your iRobot Roomba 560 Robotic Vacuum ?

My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz

Answers :

Here's the link. IR Bump Sensor Fix
\015\012Your bump sensors are malfunctioning.. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. I'd recommend them.
Repair Help & Product Troubleshooting for iRobot Roomba 560 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz

Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum

Robot goes round in circles, I have cleaned sensors, removed battery & held down start button for 30 secs

\015\012\015\012\015\012\015\012\015\012Your bump sensors are malfunctioning. I had the same problem. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. I'd recommend! ... iRobot 530 Roomba Vacuuming Robot, White Vacuum

Powers on but will not run, goes BONK when button is pressed.

OK, I have fixed my Roomba!! First I went out and searched the web for Troubleshooting info. What I found was the diagnostics that the factory uses to test them. So going through the diags. I found that 3 of the 4 IR Sensors along the front were no ... Roomba Robotic Floor Bagless Vacuum

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.

... Sebo X4 Bagged Upright Vacuum

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee

... Vacuums

The roomba or I robot will upon pressing the start button go around in circles, than starts to goin one direction, than stops and goes in a circle. The unit is clean and the unit reset. Bill

Is the front bumper **** in? ... Roomba Vacuums

My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b

WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum

Hoover U8311 WindTunnel2 vacuum cleaner will not run. When I press the start button, the Red dity light comes on but nothing else happens.

... Hoover U8311900 WindTunnel 2 Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T

... Rainbow E series Canister Wet/Dry Vacuum

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.

How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

It will work-about 1 in 50 times of trying. when i put in a file and press MDR button it makes a whirring sound and the screen will say any one of several things e.g.no disc or corrupt file.If the data file is put in before machine is switched on-i then get YAMAHA MDF 2 and nothing happens when i press the mdf button.

The unit is basically a floppy backup machine. In your case the actual floppy reading unit has failed. Since this is a custom mechanism it means that the unit is pretty much dead - no replacement parts for it. If you are willing to try everythi ... Vacuums

I have a RIVAL Vacuum Sealer Model VS150. I need to repair the power button that is located under the cover. It looks like someone pushed the button into the machine without lowering the cover. I live in Bridgewater, MA & the address on the unit is in Milford, MA. Any suggestions.

... Vacuums

Hi, I've a Tefal Steam Generator Express Turbo 2910. It won't "steam". The solenoid works when the button is pressed. The pump works. I've cleaned the tank (with white vinegar as recommended on this site!) thoroughly. The water from the steam tank is only "hot" (not scalding as I'd expect it to be). When first switched on and hot enough there is the TINIEST whiff of steam when the button is pressed then nothing more. Do you think this could be the Thermostat Part CS00094126, or can you

... Vacuums

Tried pressing in red button and switch next to on button to get roller working but not made any difference - still wont turn (any no suction)

Hi there,I'm sorry to hear you're having difficulty with your DC24. If you haven't been able to reset the brushbar using the reset switch on the cleaner head, I'd encourage you to get in touch with us directly so we can provide further assist ... Dyson Ball DC24 Bagless Upright Vacuum

George i have just bought George from a friend and he has never used the wet side of things . When i turned the hoover on i cant seem to get the wet button to work. Do i have to have the hoover main button on first and then press the wet button?

The pump can seize up if the the system is not flushed with clean water after using carpet shampoo. You should run half a tank of clean water through Geroge before putting him away.The only solution is a new pump or pump motor. ... Numatic GVE370 Canister Wet/Dry Vacuum

Err5 When charging the battery, it starts out flashing amber, but after several minutes it turns red and the err button flashes five times. The troubleshooting says to hold the buttons above and below the power button for ten seconds and this may resolve some software issues. I tried that but it goes back to the amber light then red again. I replaced the battery hoping that was the issue, but it still does the same thing.

... iRobot Roomba 530 Robotic Vacuum

My Singer Sewing machine (model 6215) is now only sewing in reverse. After pressing the backstitch button, the button seemed to stick in the backstitch position. I was finally able to pull the button out but my machine continues to only stitch backwards. What do I do now?

It's stuck inside. Open it up so you can see inside the bottom, look for the feed dog mechanism and you'll find where length of step is varied, this is where the reversing takes place too. Tapping gently and oiling will free it up.lp ... Vacuums

I have an Electrolux Oxygen 3 Ultra Canister Model No Rel7020. I am having problems with the On/Off Button and the Bare floor/Carpet Brushroll On/off button. The Carpet On/Off will not work at all. In order to turn the vacuum on, I must press a combination of the first two buttons. Is this an electrical issue

You have a problem with the electrical switches. If you are comfortable with this, take apart and double check internal wiring to make sure nothing was frayed, or disconnected. Make sure it is unplugged. If you know how to operate a multimeter, yo ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My Windsor Sensor XP12 says the bag is full when it's not. I have removed the hose, brush, and filter and cleaned everything. I can put a bag on without the cover and it works great. However, when I add the bag to the front cover and close the latch the right way, it does not work. I'm thinking that the cover is not seating the bag correctly over the hole, but I can't figure out how to fix it. Any suggestions?

... Windsor SR12 Sensor Bagged Upright Vacuum

Irobot runs without pushing power button

... iRobot Roomba 4210 Bagless Robotic Vacuum

I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?

I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums

I have a wireless thermometer made by Viking (CE 0197). Have replaced the batteries of the remote sensor RF wireless. In the battery compartment there is button TX and a slide switch for position 1,2,3. Have replaced batteries pused button but no results of recording. Could you help me what to do to make the unit work again. Thank you

... Vacuums

I have a DC 21 Dysonstowaway. Lately it cuts out a LOT, when vacumning . I press the start switch on the head, goes for 5 sec. Stops, goes, stops etc. How frustrating !! What can I do ?

Sounds like a loose power connection someplace on the machine.\015\012Probably needs to be looked at by an experienced repairperson.\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Charmglow Electric heater is not working. The problem is when i turn on all the buttons which includes blower fan, heat 1,heat 2, and firebackround motion. Only the fire backround motion goes on nothing else. I did notice that the fan button is not working properly

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0467 seconds