Having problems with your iRobot Roomba 560 Robotic Vacuum ?

Roomba 530. All new brushes and gear box clean. Brissel brush does not turn

\015 5 white plastic gears have been cleaned and washed. All new brushes and filter. rubber Rubber rotating brush works fine without brissel brush. Brissel brush only rotates when it is turning or backing up.\015

Answers :

Repair Help & Product Troubleshooting for iRobot Roomba 560 Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roomba 530. All new brushes and gear box clean. Brissel brush does not turn

... iRobot Roomba 560 Robotic Vacuum

I noticed the Roomba's brushes were not sweeping, or turning so they could sweep. There was a new sound coming from the machine, the sound of grinding nylon! Upon inspection, I determined the problem to be a heat melted gear support hole. The hole was no longer round but oblong. You could see a ridge of plastic around this hole. So melting I believe was the culprit. The gear that uses that hole was then able to tilt to one side, thereby allowing the gear to disengage from the drive train. I

Be sure to keep your brush bearings clean. If they get clogged, the brushes don't turn and the drive sockets can get damaged. ... Vacuums

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th

... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Model DC-31 Animal. Brand new out of the box. Brush turns intermittently at initial start-up then stops completely after 30 sec. to 1 minute of using. Belt is in-tact and functioning. Belt motor hand-turns with some resistance felt.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Thanks! Awesome tip to get into the gear box. My roomba would start up but would move very sluggishly. Looked up the beep code and it was the brushes. Brushes are cleaned regularly so it was something internal. Did your solution of getting into & cleaning the gear box and viola! He's back!

... Roomba Robotic Floor Bagless Vacuum

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position

I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.

Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]

Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.

... Vacuums

I followed the instructions above and found that neither brush turned. when no brushes are in and the vacum is running the gears are not turning either when i look inside the unit

You need to clean the gears hidden in the housing itself. they have become clogged with hair etc and wont turn.This will require you to remove the housing. ... iRobot Roomba 530 Robotic Vacuum

The brush roller will not turn. checked the belts, checked the brush roller gears and they are good too... the motor is not turning .. could it be a switch somewhere?

... Electrolux EL5020 Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?

This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums

REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu

Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums

Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!

Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums

I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?

Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Brushes wont turn one of the gears is striped

What is the make and model # i can check to see if what you need is available and give you a price and model # ... Vacuums

My oreck roller brush does not turn, belt is new and attached properly help

... Oreck Vacuums

I got new belts but the brush wont turn

Make sure the vacuum is on the carpet setting..the brush won't turn on the hard floor setting.. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

I hav a floormate, it is just new and I can't get the water to release on the floor to wash it. I have the dial turned to wash and I do not get any water, the brushes do turn, but no water.

I had the same problem. I brought it into a repair facility and they took care of it. It appears that the trigger mechanism is a plastic shaft that warps over time, so what they did was to "extend" the shaft so when I pull the trigger, it actually pu ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2989 seconds