Having problems with your Karcher RC3000 Bagless Robotic Vacuum ?

Notices some problem with suction on my Karcher RC3000. Much of the dust remains on the brush and doesn't get sucked in. Service couldn't advise anything. Any ideas?


Answers :

The air passages through the machine may be plugged, or the impeller (fan) on the motor is slipping on the shaft so that no vacuum is produced. Remove the brush assembly to check the air passage behind it and inspect the brush bearings for collections of thread, string, and hair. Also, inspect the debris collection area for air passage blocking. If there is a filter where the air discharges that might be plugged. Hope some of this helps!
Repair Help & Product Troubleshooting for Karcher RC3000 Bagless Robotic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Notices some problem with suction on my Karcher RC3000. Much of the dust remains on the brush and doesn't get sucked in. Service couldn't advise anything. Any ideas?


The air passages through the machine may be plugged, or the impeller (fan) on the motor is slipping on the shaft so that no vacuum is produced. Remove the brush assembly to check the air passage behind it and inspect the brush bearings for collection ... Karcher RC3000 Bagless Robotic Vacuum

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?


... Kirby Heritage II Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?


Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brush spins but the the dirt is not getting into the bag. i cleaned the hoses now it's not sucking anything up.


If the motor is running you should get some kind of sucktion, if no sucktion or wont blow any air out, check the house making sure is clear of any obtruction, the best way is looking in the house by have one person hold one end and other pull the hou ... Vacuums

There is no suction from the head on the floor. The hose is sucking properly but not the floor brush. I have checked for blockages and can't find anything - any ideas?


I have exactly the same problem!\015\012i think it is something to do with the transfer hose that changes the suction from the hose to the brushes ( it is at the bottom left of the machine as you look at it from the front! ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I accidentally sucked up a sock, now the brush doesnt roll, or pick up anything


... Dyson Ball DC24 Bagless Upright Vacuum

No "sucking" action i'm not getting any air to **** up anything, i cleaned it up put new belt on, doesn't look like there are any obstructions can't get it to **** up anything


Did you check to see if the beater brush was rotating properly?\015\012When it doesn't it usually causes the belt to burn and break, though I do not believe you had a belt issue.\015\012\015\012If you remove the beater brush like you did to rep ... Hoover Tempo Widepath Upright Vacuum - Blue

I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech


... Vacuums

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.


Model no. req ... Hoover Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

4870 Boss Smartvac. The vacuum tipped over and now the brush control lever will not stay in the carpet position. I can't get the brush to turn unless I push down and hold the lever. As soon as I let up on the lever the brush stops turning. Any ideas. The vacuum is only a month old.


The Boss has a slide lever on the top of the power nozzle with two position choices. One position is "Carpet" and the other is "hard/bare Floor". The power nozzle brush roll is activated when the lever is in the Carpet position, and it is t ... Eureka Smartvac 4870 Bagged Upright Vacuum

The brush on our Dyson DC07 isn't moving - the band has not broken, is still attached but not moving the brush. the hoover is still sucking up dirt but not brushing anything up


Check beside the on/off switch. My model has a button beside the on/off switch that turns the brush on and off. It just has a picture on it no word. Hope this helps! ... Vacuums

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

Doesn't suck I have a Hoover Empower. The motor runs, but it is not sucking anything up and the brushes aren't rotating.


Every vacuum needs to be occasionly taken apart and throughly cleaned. Usually when the brushes don't rotae it's a belt. But sometimes it's because junk gets wrapped around the roller. Things like string or thread or fiber that wounds around the r ... Kenmore 35912 / 35913 Progressive Upright Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?


If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Why doesnt my rootcycle dyson **** up! belt ok, emptied regularly, the handle bit where it sucks is fine but not the rotating brush. it sucks up fluff but not light dirt and bits. changed white pipe underneath as it was split.


There is a removable cover on the bottom of some Dysons which is like a U-Bend. On occasion this is a likely spot for blockages. Also make sure that all of your filters have been cleaned. Locate your local Dyson Customer Service from ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I can't get the latch that connects to the brush head to engage. Thus the vacumn is extremely hard to push. It has suction, extreme suction. Rollers appear to be dragging. I've tried to remove and reinstall the head several times but cannot seem to get the latch to engage. Please advise.


It sounds like something has come out of it's socket. If the brushroll won't turn rapidly, your clutch is worn out ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My vacuum blows air instead of sucking air. I have a dirt devil swivel guide. I got something stuck in the brush spinner, got it out...but now the vacuum doesnt suck stuff up anymore.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=571660\015\012Generic problem for all Vacuums\015\012My vacuum blows air instead\015\012Posted by katweaver3 on ... Vacuums

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis


Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush on my bissell helix (model 22C1-2) stopped working all of a sudden today. The hose still sucks and everything. I even cleaned the spinning brush and it still doesnt work. I just bought it in August.


... Vacuums

I put in a ne Kirby Bag and it still is not sucking up the dirt. The brush is turning but the bag does not seem to be getting any sucking snce it is not expanding


See if this helps:\015\012http://www.goodvac.com/kb_results.asp?ID=13\015\012\015\012Good Luck,\015\012Rocky ... Kirby Ultimate G Bagged Upright Vacuum

Model number f 5912-900 hoover steam vav with clean surge.This is not the f5914 model........my new machine has 10 min. on it...in mid use it has stopped sucking and now is blowing more than anything, I took the front clear piece off as well as the black cowling/shroud and can find no obvious hoses to un-clog nor anything else to un-clog for that matter...I am looking for advise to fix this thing now, myself


Here is a list to go by for no suction problems that you can follow along with they are common proble\015\012Problem #1 Steamvac is not Sucking!If your Hoover Steamvac was working properly and suddenly it is not sucking any ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I sucked up the fringe on a carpet, it didn't actually get sucked up but it did disconnect the drive mechanism in some way. Any idea how to fix this?


This vac doesn't have a reset button. You probably have a broken belt. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0855 seconds