Having problems with your Kenmore 22313 Bagged Canister Vacuum ?

Kenmore Elegance Vacuum cleaner - power bar not working

\015 Power bar starts then switches off\015

Answers :

The problem almost certainly is that the axle of the brush in your power bar has dirt/fluff in it that is preventing the belt from turning it so that the fuse in the power bar clicks off after 2 or 3 seconds. It is fairly easy to fix. All you will need is a Phillips screwdriver and about 15 minutes. Follow the following steps
\015\0121. With the power bar disconnected from the vacuum, turn it upside down and you will see two inset screws at the rear side of the base of the power bar. Unscrew these two screws using your Phillips screwdriver.
\015\0122. With the power bar in the same position unlatch the two plastic tabs at the rear of the power par. [It may be useful to flip up the metal bar that you see on the base to use as a handle] On each side of the base you will see an arrow saying insert screwdriver here to release. Insert a screwdriver and lever the plastic of the base slightly apart from the plastic of the side. When you have done this for both sides the base should lift off.
\015\0123. Now lift the brush including the two end pieces straight up. It should just slide up. You will need to unhook the drive belt from the brush as you lift it out.
\015\0124.Pull of each end piece and clean the dust, lint, hair off the end piece and from inside the end of the brush.
\015\0125.Once clean, reinstall the end pieces on the brush. Hook the belt back over the brush to its original position and slide the brush back into the power bar.
\015\0126. Reinstall the base by hooking the tabs from the front of the base into the small openings on the power bar.then push the base down until it clicks back into place and the tabs are back in their original position. Reinstall the two screws you removed earlier.
\015\0127. The power bar should now work. Good luck.
Repair Help & Product Troubleshooting for Kenmore 22313 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore Elegance Vacuum cleaner - power bar not working

The problem almost certainly is that the axle of the brush in your power bar has dirt/fluff in it that is preventing the belt from turning it so that the fuse in the power bar clicks off after 2 or 3 seconds. It is fairly easy to fix. All you will ne ... Kenmore 22313 Bagged Canister Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

My power nozzle has stopped working. The vacuum itself is still working but not the power bar. I would like to order a power nozzle. Can you tell me how I can order a nozzle for a Kenmore Whisper Belt 12.0 amps

... Kenmore 23313 Whispertone Bagged Canister Vacuum

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks

... Kenmore 23313 Whispertone Bagged Canister Vacuum

We have a Kenmore canister vacuum cleaner. the carpet cleaning attachment, I think is called the power mate has a beater that is intermittently working now

Contrary to your advice, the nozzel cannot be connected directly to the powerhead--the female openings are set closer together in the nozzel than the male plugs in the powerhead. ... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

Have a kenmore canister vacuum cleaner which the power-mate parts don't work. I had loaned the vac out it came back with part of the hose smashed. I don't know if that is the problem.

The hose conducts power to the "power Mate" There are wires running end to end through the hose and handle. If your hose is grey with hard plastic cuffs at both ends, it is repairable, but you will need to locate the Smashed parts. If yo ... Vacuums

Our Kenmore Elegance Hepa Filter vacuum has just suddenly stopped working, bag was full, changed it and now no power.

... Kenmore Vacuums

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank

You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope

Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!

... Kenmore 25512/ 25513 Progressive Canister Vacuum

The power head on my kenmore 22822 Canister Vacuum won't work? the power upholstery head works fine.

I have the kenmore whisper belt and i have a reset button on mine ... Kenmore 22822 Canister Vacuum

Hey I have a kenmore model 116.23185800c vacuum. The vacuum stopped working but the power head still works is there a reset for the motor

... Kenmore Vacuums

We have a Kenmore canister vacuum cleaner and the power in the floor component (rotating brush, etc) is no longer functioning. The vacuum is producing suction, but does not seem to be providing power to the floor component.

The problem could be with the power head itself or the hose providing the power. If you can turn the unit on from the handle, then its not the hose and you need to get a new power head.. ... Panasonic Kenmore Canister Vacuum Vacuum

A family member recently gave me their Kenmore Vacuum Cleaner (model 35821) and I did not notice that the power cord was missing at first. I tried to look closely at the manual online to see if this was something I would be able to purchase or if the vacuum was no longer any good. Do you happen to know if there is a replacement part for the actual power cord for this item?

Any power cord 17 gauge or lower will work ... Vacuums

Kenmore vacum cleaner model 11628615801 has power but vacum motor doesn't work

... Vacuums

We have a Kenmore canister vacuum cleaner 25614504. It has in intermittant light and power flicker in the power mate unit as it is moving over the floor. This behavior can be simulated by jiggling the power cord where it eners the power mate. I do not know how to enter the power mate to see if there is a loose wire.

... Kenmore 28614 Canister Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

How to take apart beater bar of kenmore vacuum cleaner model 116

... Vacuums

My kenmore model no 116.22512200 canister vacuum power head has no suction & doesn't pick up even though it shows all the signs that it is getting power. The junior power mate works fine.

... Kenmore Vacuums

Kenmore vacuum model 116.52450200C- beater bar not working

... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

The Vacuum canister is working but the tip did not havesuction power. Should I change it? Where can I finf the repair shp in my vicinity. My area is Ravenna, Ohio 44266. My Vacuum cleaner is about 10 years old similar to Ultralux 2000.

Try checking for blockages first, turn the foot of the vaccuum over and check the inlet tube, there may be a little flap that needs to be pulled forward for you to see if there is a blockage. ... Electrolux Vacuums


Hi its Darran at Dyson. From your description of the problem, either the brush control has been switched off (dial on the side of the cleanerhead) or the belt has snapped which may indicate a problem with the clutch. Please ca ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Rod problem... One of the electrical connection posts that are on the top of the rod appears to be broken which causes the power head to work only when it makes contact. Is this repairable? If not, is it replaceable? If not, are the rods available for purchase? The vacuum cleaner itself works well,

You would need a new wand. this might work for your unit. ... Fantom Vacums Lighting Canister Vacuum

Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.

... Sanyo Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1379 seconds