Having problems with your Kenmore 22812 Bagged Canister Vacuum ?

Intermittent Power brush

\015 I'm on my second Kenmore canister vac, and after a few years they have both had this problem. As you vacuum, the power brush is fine when you push it forward, but seems to die a little on the pull back. Almost like a connection is coming lose a little. Any suggestions of what I can do to fix, or tighten this? Thanks!!\015

Answers :

Dirt gets inside and causes an intermitten problem on the hose where it connects with the canister there is a plastic cover where the three pins stick out. on the cover are two tabs on either side. press both tabs together and CAREFULLY pull cover off. on the hose are three rings,clean them off with a rag,then put a small amount of grease on them. with this done go to the cover. you will see a small part with the three pins. on top of the pins are flexable leads. CAREFULLY pull up on them,but not much,only a little. now clean the inside of the cover. now lets put it together. first take the small part with the pins and place it on the hose making sure that the flex leads match with the rings. now place cover over both til it snaps into place. BY GETERDUN
I would first check where the hose attaches to the canister. There are 3 power leads; if one is bent, this might produce what you describe. You might even try wiggling this connection to see if it affects operation.

The other place you might see a problem is where the hose connects to the handle itself. There are 3 wires that attach from the hose. This is a bit tricky to remove as it's basically a force fit and take some effort to remove.
Repair Help & Product Troubleshooting for Kenmore 22812 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Intermittent Power brush


Dirt gets inside and causes an intermitten problem on the hose where it connects with the canister there is a plastic cover where the three pins stick out. on the cover are two tabs on either side. press both tabs together and CAREFULLY pull cover of ... Kenmore 22812 Bagged Canister Vacuum

My electrolux sidekick, model 1562 makes a nasty screeching sound.It happens as soon as it is powered on,the noise then gets intermittent after qa few minutes and then goes away.This cycle is repeated evry time i use it.I have checked it for binding and obstructions and oiled the motor.I think it's the roller brush but oiling it didn't seem to help


... Electrolux Vacuums

Miele S514 Solaris Electro Plus with Power Brush. Bought it in 2003. I love it, except the Power Brush just lost power so now I can't vacuum the carpets. I believe it is a SEB 212-2 Power Brush. The vacuum (canister) is Black. Any help is appreciated. There is no power to it at all. I've unplugged it, smacked it around a little too (mostly kidding) but still nothing.


... Miele S514 Solaris Electro Plus Vacuum

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.


First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.


You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help


Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david


Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.


Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

I just bought a Z1750 twin tech vacuum. I am wondering if I can buy a power brush attachment for this. It only comes with the floor and "carpet" brush but does not have the beater bar (power brush).


... Electrolux Centralux Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

Power head just quits intermittently, red lights flash on


... Vacuums

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Can you tell me if Powermate Power Brush attachments are all the same for all the Sears Powermate Cannister vacuums.  That is, would one power brush attachment on a Model 116.56512690 fit one that is Model 116-22512202?  Are the connecting ports all the same size?Thanks for your help.


I think your confusing model #s ,as the 116. 22512202 is the canister model number and the model number of the powerbrush attch would be 116.52512202,but to answer your ? no it depends on which wand your useing that determans which one you can use ... Kenmore 22812 Bagged Canister Vacuum

Electrolux power nozzle, model 1692, power cuts on and off. I don't have the manual for it, but I'm trying to remove and clean the brush compartment. I removed the top, but not sure how to get to the brush. I would like to find a manual for it, because it's completely different than the one I use to have.


... Electrolux Vacuums

No suction power ,brush wont spin on carpet power nozzle. When it


You need to replace the belt that turns the brush. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Just purchased this Dyson dc24 today. brush doesn't spin after gettin tangled in a cord. removed the cord from the brush OK. I have several times: removed the brush and replaced it OK. pushed the red button by the brush. pressed the brush power switch.


When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not roun ... Dyson Ball DC24 Bagless Upright Vacuum

We have a Kenmore canister vacuum cleaner 25614504. It has in intermittant light and power flicker in the power mate unit as it is moving over the floor. This behavior can be simulated by jiggling the power cord where it eners the power mate. I do not know how to enter the power mate to see if there is a loose wire.


... Kenmore 28614 Canister Vacuum

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

I have a bissell pro heat model 7901-B that has power but no water circulation. I was told that the previous owner used it without water and that she couldn't get it the power on. I bought it off of her and cleaned it out and now the power works, but there is no water circulation. The brushes run and heater works, just can't seem to get it to circulate water. Thankyou for your time, Don


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The brushroll on my dirt devil (vax X3) was caught o the curtain, and now the reset button will not reset the brush. the power comes on for the brush, but the brush will not rotate. What can i di to fix this problem


I didn't find the reset button until I took all the screws out and then couldn't separate it. Good luck! ... VAX Appliances Vax X3 Bagless Upright Vacuum

No power. I was getting intermittent power with my miele s558 midsize canister, but it was predicated with me fiddling with the retractable cord to get it to come on and then not move the canister while I was vacuuming. Now I can get no power. I have taken it apart and can see no issues with connectors, cord, casings, etc. It all looks fine. It is about 5 years old and I have had no problems with it.


... Miele S558 Red Velvet Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0585 seconds