Having problems with your Kenmore 22812 Bagged Canister Vacuum ?

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


Answers :

If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad.
Repair Help & Product Troubleshooting for Kenmore 22812 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

Vaccum brush not working. Filters clear of debris has been smoking will not **** anything up help! I cleaned the brush up, cut hair out, etc. Still the brush will not turn and it smokes a little, is this a belt problem?


Yes you need to change the belt. Here is a link to the belt you need and to a manual you can view:Bissell Lift-Off Revoluti ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a roomba 435. I've had it for about 3 months, it had been working great until it started to sound a little different (louder). Now I noticed that it doesn't pick things up, it just pushes them around, I then discovered that the brushes aren't turning. I cleaned them out, no parts are missing. Brushes still won't turn. Help please.


Hmmmm....I know exactly what this is... Think back...the last time it was used when it worked...did it pick up something like a sock or get stuck somwhere?????? If you look on Ebay, it is polluted with this model Roomba. There is a gear that strips. ... iRobot Roomba 410 Robotic Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?


Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

I have a Bissell proheat clearview 12 amp 5 cleaning rows of dirtlifter powerbrush. It won't shoot the cleaner to the brushes. I cleaned the filter, checked the belt, water is full, and soap dispenser is full. Still no soap going to rug. Can you help? Thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

My dyson dc 07 brush will not rotate. I have cleaned all hair and debris from around the brush and no change. I can not even figure out how to look and see if the belt is still attached. Suggestions?


DC07s are not easy to check the belt on, in fact depending on which exact model you have there are probably two belts.\015\012One connects the output of the motor to the clutch mechanism (one end of which has the control knob that ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush roller on my vacuum will not move. I've cleaned it, checked the belt, but when I put the roller back it, it will not move...almost like it is in a locked position. Everything has been done correctly from the book yet, it still does not move. Any help PLEASE?


... Electrolux EL8502 Versatility Bagless Upright Vacuum

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin


Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!


Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

The brush stopped on our DC25. Husband said sparks were coming out of the bottom near where brush is. Brush was cleaned of hair and string. Brush still does not spin. I saw no belt on the brush. Should there be one?


... Dyson DC25 Animal Bagless Upright Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?


Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!


... Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda


Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0886 seconds