Having problems with your Kenmore 22812 Bagged Canister Vacuum ?

Sears canister vacuum

\015 The problem with the sears canister vacuum is the power head doesnt always run. the suction is there but its like its not getting an electrical connection. the 2 prongs look a little rusty, so we have used an emery board file but it is still happening.\015

Answers :

Repair Help & Product Troubleshooting for Kenmore 22812 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have no power on a brand new Electrolux Oxygen canister vacuum. This is the second time. After the first time, I took it back to Sears where I bought the vacuum and they gave me a brand new vacuum. This is the second time it's happened, basically on both units after the time that i brought them home.


Ensure that the tools and the bucket are installed properly, if the bucket is not well in place, the unit wont start.If the electric power does not come on, disconnect from mainsand check plugs, cable and fuses where appropriate. ... Electrolux Vacuums

Sears canister vacuum


... Kenmore 22812 Bagged Canister Vacuum

I have a bad connection on my powercord on my Whispertone 300 Sears canister vacuum 116-28612790. How can I access the autowind cord/get into the canister?


Seems like a personal problem, ... Kenmore Vacuums

Need a repair Manual for Sears Kenmore Canister Vacuum with Powermate that was purchased in March of 1999. Only numbers we have are as follows: 20-29712-990; 116.29712990; and 116.59712990. The canister is making a clicking noise when shutting down and we don't see how to get to the inside of the unit as it doesn't have any visible screws. Thank you for any information.


... Vacuums

How do I change the belt on my Sears vacuum? - Kenmore 25512/ 25513 Progressive Canister Vacuum


Hello,Here's what you'll need to replace a belt on a Kenmore ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Owner's manaul for sear's whispertone vacuum - Kenmore Whispertone 23312 Bagged Canister Vacuum


... Kenmore Whispertone 23312 Bagged Canister Vacuum

Motor Brushes (Part 4370655) for Sears Canister Vacuum Cleaner


... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

Sears canister vacuum stopped working after catching my blanket


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Sears Model 116 25915500 - Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Sears canister vacuum rear wheel won't stay on


1) test the power cord for open, defective, or break use the VOM 2) test the fuse for open, loose wire use the VOM3( tes the motor, for open, short, or defective, need repair.4)test the switch, for open, or loose wires, or short.see h ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Removing hepa filter on sears model 116 - Kenmore 25512/ 25513 Progressive Canister Vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Sears canister vacuum - hose swivel replacement- release conn.


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Sears kenmore canister vacuum cleaner model #115.78423210 serial #cj08312085932


... Vacuums

How do i remove the reel cover for my SEARS canister model 116312690 vacuum cleaner. we are unable to move the cord forward or back. We have found two screws, but are still unable to remove the cove


... Kenmore Vacuums

Hi, I have a Kenmore Whispertone canister vacuum that I purchased in 2007. The model # is 116.22271503C, which seems to confuse the parts people. I need to buy a new powerhead & a few months ago was given a price of $75, but now Sears Canada tells me the part # is 20 116KC5OXBZRZUO1 described as Power Mate Assembly for $192.99. I thought the Power Mate was the small powerhead for stairs, upholstery, etc. Have they located the wrong part for me, or is this really what it costs?? Thanks in advance


Yes, powerheads are quite expensive. That sounds about right.\015\012You can check Ebay for better prices, but check the shipping rates before ordering. ... Kenmore Whispertone 23312 Bagged Canister Vacuum

I have a small sears canister vacuum. The beater bar wasn't working so I took it apart. Do you have a picture of how to put it together again.


... Kenmore 22812 Bagged Canister Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope


Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I'm sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip


Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond ... Hayden Industries SuperVac 6000 Central System Vacuum

My Hoover s5620 central vacuum is not sucking. I cleaned out the canister and vacuumed the inside bag in the canister. The hose is clear as is the central vacuums tubing. Any suggestions ?


Try getting some compressed air source and blow back whatever is stuck in the hose. ... Vacuums

Overheated vacuum After I finished vacuuming the library last night I changed the bag and shook out both filters and vacuum would not restart. The canister unit felt real warm to the touch but I had been using it a least 1/2 hour non stop. The bag was pretty full but not overly so. It's a Simplicity canister with power head. The carpet is long shag from the 70's Did it just over heat? Thanks Shauna


It normally won't over heat unless the bag is too full, the filters are clogged, or you have have a clog in the hose or down by the brush roll, the inlet may be clogged. Some will restart after a while, some others have a reset to push. If it won't ... Simplicity 7850 Premier Bagged Canister Vacuum

25512/ 25513 Progressive Canister Vacuum: HI, we have a kenmore progressive canister vacuum ...


Cord bad at male prongs, or fuse near motor blown. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

The canister bag keeps ripping on my Kenmore Vacuum model 116.23201C


... Kenmore Vacuums

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

How do i open my canister vacuum - Electrolux UltraLux 2000 Bagged Canister Vacuum


Open the bag door and grip the bumpers with a set of pliers. The bumpers cover a set of locking keys which will slide all the way forward and out. The back of the vac will then lift off and the top and bottom will open hinging forward like a **** she ... Electrolux UltraLux 2000 Bagged Canister Vacuum

The foot pedal on my Kenmore upright vacuum cleaner has broken three times. The vacuum model number is 116.33923 and the Sear's part number is 8174906. Does Sears make this part in metal instead of plastic? It is becoming expensive to keep replacing this piece when it costs around $20 each time (including shipping) Thank you for your time. Jerry DeWulf


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0565 seconds