Having problems with your Kenmore 22822 Canister Vacuum ?

Kenmore cannister vacuum tube - reattaching connectors

\015 Any thoughts would be helpful...I have replaced the connector that connects to the cannister and the tube. I was able to wire everything up and test, but now despite large efforts of pulling / pushing I cannot get the clips to click. Any ideas?Thank you for any help!!!\015

Answers :

Make sure that the two prongs that go over the hose are going in the correct slot in the cuff. If in the wrong one, the cuff won't snap into place. I have had to slam the end of the hose on the work bench while holding the cuff to push it all of the way on. Some I have heard warm up the cuff in hot water or a hair dryer to make it more pliable.
Repair Help & Product Troubleshooting for Kenmore 22822 Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore cannister vacuum tube - reattaching connectors


Make sure that the two prongs that go over the hose are going in the correct slot in the cuff. If in the wrong one, the cuff won't snap into place. I have had to slam the end of the hose on the work bench while holding the cuff to push it all of th ... Kenmore 22822 Canister Vacuum

Hi, I have a Kenmore vacuum cleaner model number 20712008. There seems to be a problem with power getting to the suction base. There may be an electrical problem with the connector between the metal tube and the base.


... Kenmore Vacuums

I have a Kenmore Destiny Plus vacuum, and it doesn't have suction anymore. I've come to the conclusion that the tubes, I guess you can call them that, are plugged. I'm trying to find the user manual/service manual to know how to open the vacuum up to unplug the tubing.


It's October now so this is probably too late to be useful for you but it might help someone: I had the same problem. I used a bright light to see that there was a clog up high in one of the plastic tubes on the side. Using an untwisted wire coat han ... Kenmore Vacuums

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

The vacuum does not **** in dirt. It is blowing air instead. Yet when I disconnect the vacuum from the cannister, the suction seems very strong. I took it to a vacuum repairman, and he said that Kenmore sucks and I might as well get rid of it. (He wanted to sell me another one) It is 10 years old, but if I can fix it I would like to try.


... Kenmore 22613 Bagged Canister Vacuum

Kenmore PowerMate cannister: Reattach cannister floor piece.


You need to open the head by gently squeezing the light cover housing and lifting it off. There will be two screws underneath and once removed the lid will lift off and reveal the area where the pedal installs. ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

KENMORE 27614 CANNISTER VACUUM The roller vacuum brush does not rotate. I check the belt and it is fine. Waht could be the problem?


... Kenmore Vacuums

Kenmore Cannister Vacuum Model 26312


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=109396&thid=552260\015\012Kenmore Canister Vacuum Model 26312\015\012Posted by Alecia Rojas on Apr 28, 2008 ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Kenmore cannister vacuum model 116.2411290 has begun exhausting a 'burned' smell. Suspect bad blower bearing. How to access?(Can't find manual online.)


Hi,how are you so sure the problem is from the blower bearing and not the belt,well to know if the problem is from the blower bearing or the belt you have to know how to access your vacuum first,so from all angle you need the manual You can download ... Kenmore Vacuums

My Kenmore Quick Clean vac clogs at the top of cannister and does not let dirt to go to canister. After vacuum for few minutes have to stop empty before continuing to get rug clean. Is there anything that I can do to solve problem.


You need to own an air compressor,and blow out all vacuums ,after each use. ... Kenmore Vacuums

Won't ****, tube is not clogged - Kenmore 25512/ 25513 Progressive Canister Vacuum


Re-place the bag somthing has to be blocked up check power head if it has felter clean them.see if this works write back we well fine the problem.thanks ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

I have a kenmore upright vacuum model #116.35922500. The agitator tube doesn't turn. It doesn't have a belt for the agitator. It has an overload protector. I reset it, but it keeps poping back up. Should I replace the overload protector?


The reset is for your safety no belt ,probly a direct drive motor issues ,maybe the brushes it is detecting a short and pops the reset. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

My kenmore vacuum is sucking up the dirt but continously but its not dispersing into the cannister. could it be the filter need to be changed. the dirt is collecting in the hose lines.


Make sure your airway is not plugged and then it maybe the filter sometime just a tooth pick would give you a problem ... Kenmore Cyclonic Action 39259 Vacuum

I have a Kenmore upright vacuum cleaner Model No 116.35922500 and the orange and red lights stay on all of the time. I have cleaned out the round tube where the bag fits like the manual said but it still happens


... Vacuums

No suction My Kenmore Progressive Cannister Vacuum has no suction. The hose is not clogged and I don't know what to do.


If the motor is running and is not full of dirt, and the hose is not plugged, the canister must be cracked or open somehow. ... Kenmore 22812 Bagged Canister Vacuum

Cannister model#11627915701. connector terminals in extensionwand ,and wlre harness in hose handle get hot,,,look a bit singed.. can order and do ourselves. but would like a "tune up " ,cleaning of vacuum as well. purchased in 2008. have long haired dog,,,can't afford to be without it for very long. have sears store in clay ,ny. lady I spoke w/ says it would get sent out and take at least 2 weeks.!


... Kenmore Vacuums

Kenmore evo cannister vacuum model 116. Problem: low suction. I dropped it. How do i open it to fix it.


... Vacuums

The telescoping wand on my kenmore magic blue cannister vacuum stopped working shortly after I bought it a few years ago. After 10 minutes of pushing sometimes I get it to work. It gets longer easier than shorter. What could be causing this problem? Please help!


... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks


Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.


Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

I have a Kenmore progressive cannister vacuum cleaner.


There should be a pile height pedal on rear of the attachment, just behind the where the wand goes into it, near the handle release pedal. Just keep clicking on it to go through the height settings.\015\012\015\012Please rate if this hel ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore progressive cannister vacuum check bag light keeps coming on and ive changed the bag


... Vacuums

I need manual for kenmore vacuum , cannister 11625614506


... Kenmore Vacuums

Kenmore Model no.116.29319800 Cannister Vacuum Cleaner manual


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0720 seconds