Having problems with your Kenmore 23313 Whispertone Bagged Canister Vacuum ?

Vacuum base removal-kenmore whispertone 300

\015 I am trying to remove and replace the base on my vacuum.There are four screws. I have removed two of them. The oter two are under the retractable cord button.I need to know how to get at those.thank-you\015

Answers :

Most of these you have to take off the cover on the back end where the cover retrack button is. Usually it has a catch, 2 on each side, use a screw driver, pry up near each corner to release it, then you can get to the cover over the moter and cord reel. Remove the 2 screw and put up and out.
The front two screws are located under the front cover hinges. These screws can be accessed by opening the front cover as you would if you were changing the bag then continue to rotating the front cover and it will come off. The two rear screws are located under the cord rewind foot pedal. There are four plastic tabs holding the four pedal hinges in place. These tabs can just barly be seen by prying the pedal backward away from the rear cover. All four tabs must be pressed forward (I did it one at a time) then rotate the pedal up and forward until the hinges pop out of their sockets. It's tricky and frustrating but it can be done.
Repair Help & Product Troubleshooting for Kenmore 23313 Whispertone Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vacuum base removal-kenmore whispertone 300


Most of these you have to take off the cover on the back end where the cover retrack button is. Usually it has a catch, 2 on each side, use a screw driver, pry up near each corner to release it, then you can get to the cover over the moter and cord ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Sears Kenmore Whispertone Vacuum Problem:


If you push inwards on each side of the light cover on top you can remove it. With the light cover removed remove the (2) access screws. Now you will be able lift of the entire top cover from the base. You will then see the belt and roller brush, rem ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Hi, my Dyson DC16 works fine but after removing from charge base following recharge the red and green lights remain lit and the unit will not operate until i remove the battery and reconnect to vacuum,this extinguishes the lights and now can use with no problem.I guess that the charge control within the vacuum is not recognising that the unit has been removed from charge,is there a solution? Thanks


... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Belt for kenmore whispertone 116.26512690 - Kenmore 23313 Whispertone Bagged Canister Vacuum


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Describe how to open a whispertone vacuum - Kenmore 23313 Whispertone Bagged Canister Vacuum


... Kenmore 23313 Whispertone Bagged Canister Vacuum

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

What is the bag for Kenmore whispertone 300 - Kenmore 23313 Whispertone Bagged Canister Vacuum


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Disassemble 840 kenmore vacuum cleaner - Kenmore 23313 Whispertone Bagged Canister Vacuum


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Owner's manaul for sear's whispertone vacuum - Kenmore Whispertone 23312 Bagged Canister Vacuum


... Kenmore Whispertone 23312 Bagged Canister Vacuum

Kenmore whispertone 12 amp canister vacuum - Kenmore Vacuums


... Kenmore Vacuums

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak


... Kenmore Progressive 35922 Bagged Upright Vacuum

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Hi, I have a Kenmore vacuum cleaner model number 20712008. There seems to be a problem with power getting to the suction base. There may be an electrical problem with the connector between the metal tube and the base.


... Kenmore Vacuums

Manual Kenmore Looking for a manual for the Kenmore Whispertone 12.0 Amos Vacuum


... Vacuums

Kenmore whispertone 12.0 amp - Kenmore Vacuums


... Kenmore Vacuums

Kenmore whispertone 12.0 bags - Kenmore Vacuums


... Kenmore Vacuums

Kenmore power cord will not retract - Kenmore 23313 Whispertone Bagged Canister Vacuum


... Kenmore 23313 Whispertone Bagged Canister Vacuum

My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Remove cover on kenmore vacum model 116 - Kenmore whispertone 100 model 116


... Kenmore whispertone 100 model 116

Removing kenmore vacuum Canister motor cover model 116-27312790


What you need to do is take it apart and look for any carpet peices dug up in there preventing the motor to spin. Also go look for another filter for it and if you google it you can probably get instructions or if you still have the book. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Problems with Kenmore Whispertone model 118 Bagged Canister Vacuum Overload Protection Reset won't reset


... Kenmore Whispertone 23312 Bagged Canister Vacuum

How to remove on/off switch on 726 kenmore vacuum


... Kenmore Vacuums

Motor needs to be replaced - Kenmore 23313 Whispertone Bagged Canister Vacuum


Are you sure its the motor and not a inline fuse or brushes? How did you conclude it's the motor? ... Kenmore 23313 Whispertone Bagged Canister Vacuum

How do I remove the dust bin from kenmore grab'n go vacuum, 12 amps model 116.34723401


... Kenmore 34723 Grab-N-Go Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1133 seconds