Having problems with your Kenmore 23313 Whispertone Bagged Canister Vacuum ?

Push the reset button

\015 I pushed the reset button on the vacuum but it doesn't stay in and the belt doesn't work\015

Answers :

Sounds like a problem I had. However, I took the vacum head apart were the belt is to get to the switch that was sticking. the model # on this part is:
\015\012Mel Rain/littel fuse
\015\012HOLD 2.0 A.
\015\012125 V.D.C. / A.C. 60Hz
\015\012I took the two connectors of and carfully removed the part. After removal I took apart with a small flathead screwdriver and reset but this is a quick fix and my vacuum begin to work again!
Repair Help & Product Troubleshooting for Kenmore 23313 Whispertone Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc25 schecking continuity on reset switch its a 91 series 2 amp switch but whether i have button pushed or not a get continuity shouldn't this break when button is pushed

... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson DC24 instructions say to push the red reset button for the roller bar. My vaccuum has no red reset button. Where is it?

... Dyson Ball DC24 Bagless Upright Vacuum

Push the reset button

Sounds like a problem I had. However, I took the vacum head apart were the belt is to get to the switch that was sticking. the model # on this part is: \015\012\015\012Mel Rain/littel fuse\015\012742332\015\01211200000-04 ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?

... Easy Flo EF2300 Central System Vacuum

While operating machine, brush does not rotate. Button is pushed in, all hair cleaned off brush. Is there a reset button? Where is it located?

Likely the wires are broken under the left hand cover not a difficult fix. Unplug the machine and remove the 4 torx screws and an access panel at the side of the ball. replace wires with new or re-connect with a splice. ensure wires are long enoug ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson 24. I just bought a new Dyson ball 24 and the brush won't turn on, I tried to follow instruction and push the red button to reset it also next to the power button but doesn't do anything. Any suggestion.? Thanks Sam


The motorized wand attachment keeps shutting down after 10 to 15 seconds after pushing the red reset button. I've thoroughly cleaned dirt/debris from around motor. Do I need a new reset switch? Thanks, Tom

Either the reset is bad or the motor is drawing too many amps and tripping the reset. Do you have an amp meter? Check the amps being pulled by the wand attatchment against the load recommended by the manufature, this is usually located on a plate som ... Rainbow E series Canister Wet/Dry Vacuum

My roomba wont work. Pushing the power button doesnt do anything. It charges seemingly normal, going to green in a few hours. ive tried the reset trick, holding the power button down with the battery removed. Now what? thanks

... iRobot Remanufactured Roomba Vacuum Cleaning Robot with Scheduler, Case/Color May Vary Robotic Vacuum

Agitator stopped rotating, has checked for clogs, cleaned agitator, and pushed reset button, but still not rotating. Any ideas?

Try changing the belt ... Vacuums

My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Pushing reset button does not restart unit is receiving power, as light goes on.

... Riccar 8650/8625 s Vacuum

Every 3 swipes on the floor I have to push the reset button to engage the roller brush. Is this normal and if so why?

No, it is not normal for the brushroll to stop that often. You may need to clear any thread, etc from the brushroll underneath the vacuum. Remove the screws from bottom of unit, stand unit upright, turn height adjustment dial to either side to allow ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Brush won't turn (beltless model) even when pushing reset button

There is a floor select switch "ON" for the brush? Did the overload protector switch trip? There is a little red button sticking out from the right hand side of the head. Check to see if it is perturbing past the cover. If so, push button in and it s ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?

If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

The motor in the power head ran at a higher pitch for a for 8 to 10 seconds then stopped. If I push the reset button the powerhead may or may not start or it may start and run for a few seconds. The brush is not caught.

Did you check the belt? A broken belt results in lower strain on the motor, causing it to run faster resulting in the faster speed and higher pitch. This could result in overheating, which will cause the motor to shut off.\015\012If this isn' ... Electrolux C101 Bagged Canister Vacuum

The roller on my Dyson DC24 quit rolling. I've taken out the brush, cleaned it, replaced it, locked it and push the reset button but it still isn't rolling. Help!!! I've only had this for about two months.

... Dyson Ball DC24 Bagless Upright Vacuum

Eureka Boss - Belt is not broke but brush will not turn. I have already turned it over - checked belt - and pushed the reset button.

The belt may look fine but they can still be stretched or worn and it won' turn the brush. Try changing the belt and see what it does. You can get Eureka belts here: ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The power head model #116. 53812300 does not stay on. When I push the belt reset button it only stays on for a second or so. The belt is not jammed or the roller.

... Kenmore Vacuums

I have a Kenmore Progressive with Direct Crive Model 116.35922502 I was sweeping and my sweeper just shut down, I pushed the reset button and it is not working to either. What do I do now?

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

The vacuum comes on but the standup vacuum assessory won't turn on. I"ve pushed the reset button; unhooked everything, including reattaching the canister but it still wont' come on. Any other ideas? By the way, I hated the price, but it's the best vacuum I've ever had - especially when I have three shedding pets!

Check the roller brush to see if anything is wrapped around it. If not, there may be a loose connection or wire between the canister and the power nozzle. I assume that's the accessory you're referring to. I could also be a defective switch, but loo ... Vacuums

Beater bar lost power - even after pushing reset button

Hi There,If you've already tried resetting the power brush, and it still won't come on, this indicates that your electrical hose has most likely gone bad, and needs to be replaced.This is actually a pretty common problem on Pa ... Panasonic MC-CG973 Canister Vacuum

Beater bar does not turn. Pushed in motor Reset button after clearing bar, but no change.

Belt broke and needs replaced. ... Kenmore Vacuums

I have a DC 18 and the brush will not go around. Pushing the reset button does not help. What is the next step

Have you cleaned the brush? you can open the cover and take it out and clean it, theres a screw you can turn to open the cover.after you have cleaned it completely make sure you place it back in the same way and then press the reset butto ... Vacuums

Halo beater bar has quit working. bar (that belt is wrapped around) connected to motor is not turning. have pushed reset button. k.r.

Take it to an oreck dealer. duh ... Vacuums

Brushes Describe your problem brushes won't turn pushed reset button

Try changing the belt ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0243 seconds