Having problems with your Kenmore 23313 Whispertone Bagged Canister Vacuum ?

Broken power head belt

\015 I need to replace a broken belt and\302\240i don't know how the power head come apart?\015

Answers :

To see and get to the two slots and catches, flip the assembly over. There should be directions molded into the plastic on each side closer to the rear than the front. When replacing the belt, it will pull on the beater bar, causing it to dislodge on the belt side, and making it difficult to put the top and bottom back together. To cheat, take a long screwdriver (slotted) and use it to hold the beater bar down from the outside. This makes reassembly a breeze.
Also, remove the bulb prior to reassembly, and put it back when the two screws have been seated.
The top cover covering the light, push in at the sides to release the tabs holding it, then there will be 2 screws, remove them, then with a screw driver, on each side you will see a slot, put the screw driver in ther and pry up to release the catches. Then you can get to the brush roll and belt.
Repair Help & Product Troubleshooting for Kenmore 23313 Whispertone Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Broken belt I have a royal canister model 4750 with a broken belt on the power head. I don't know how to disassemble the head to get at the belt.

If you have the power head with the headlight, squeeze the sides of the upper part (almost like a superstructure,) where the headlight is located. It should lift off, allowing access to the screws to get the powerhead apart the rest of the way, and o ... Vacuums

Broken power head belt

Not sure which one you have, need complete model number. You can go tosears.com, click on the parts link, enter you model number, click on the powerehead link. A parts list will come up along with a picture breakdown of it.\015\012Alot of the ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

Broken power head belt

To see and get to the two slots and catches, flip the assembly over. There should be directions molded into the plastic on each side closer to the rear than the front. When replacing the belt, it will pull on the beater bar, causing it to dislodge ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Broken belt in Royal Pony power head

We have a Royal Pony as well. Here is their general help desk number. Just call them and give them the model number of  you tank. it's on the bottom of your machine. 1.800.321.1134 ... Vacuums

My kenmore progressive canister vacuum's power head has stopped working. When I check for suction from the hose, it seems strong. Could it be a belt has broken? Is this a repair that I could do myself? Thank you!

... Kenmore Vacuums

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.

Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?

Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

Chang the belt in my kenmore power mate power head

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode

... Hoover Vacuums

How do you change a belt for the belt on the Royal Part #2-470010-801, Power carpet head attachment for the Royal Classic Power Team canister model #4750?

... Royal Vacuums

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.

I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

How do I change the belt on the Miele vacum SEB234/236 Power Plus (power head)

... Miele Vacuums

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

Cant rember how to replace the belt on the power head

1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off of the Kirby's driveshaft but on the "hook" inside the power nozzle) 2)Remove the power head from the front of the machine. Now that it i ... Kirby G4 Bagged Upright Vacuum

Change belt How do I open the power head to get to the belt to change it?

... Beam Rugmaster Plus Belt

I have the Miele S175i Powerhouse Plus and it vacuums fine, but the bottom piece of the vacuum is broken. The head of the vacuum swivels freely and doesn't lock into place. Also, the connecting belt is messed up. How can I fix the head so that it doesn't swivel freely?

... Miele S175i Bagged Upright Vacuum

Miele White Star SEB 204, powerhead stopped spinning. brushes are clear of debris, belt (#3854940) is not broken. Could belt be stretched so that brush head does not spin?

Yes, most likely the belt has stretch. Flat belts do this after a short time and need to be replaced when problems start with the brush roll not wanting to turn. Also check the brush roll, make sure that the ends turn freely, if not, then replace i ... Miele Vacuums

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.

Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

The power head model #116. 53812300 does not stay on. When I push the belt reset button it only stays on for a second or so. The belt is not jammed or the roller.

... Kenmore Vacuums

I am trying to disassemble a Kenmore Powermate vacuum head in order to access the power head belt.

Squeeze the sides of the lamp cover, and it will snap off. then you will see 2 screws under where it was the rest is obvious ... Vacuums

I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...

Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums

Not working bissell power pro carpet cleaner not working. was working fine, then I smelled rubber like a belt had broken. does it have a belt that can break.

The bissell shampooers use belts t run the pump and the beater bar. if the master beltbroke which is the one that controls the pump and beater bar then yes the machine will not dispense water or turn the beater bar. it will have to be replaced *the ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?

I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Belt & motor replacement electrolux z8280 power head

... Vacuums

Change belt on Hayden power head

... Hayden Industries Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0878 seconds