Having problems with your Kenmore 23313 Whispertone Bagged Canister Vacuum ?

Change the belt in my kenmore power-mate 120 amps...how to open it to get to where the belt is???

\015 Don't worry...I dont expect any help...just a shot.\015\012have a good day.\015

Answers :

HELLO, JUST REPLACED THE BELT ON OUR'S. FIRST TAKE LITE LENSE OFF THERE WILL BE 2 SCREWS, REMOVE. THEN FLIP OVER POWER MITEON EACH SIDE PRY WITH 2 SCREW DRIVERS WHERE THE ARROWS ARE TO SEPERATE & THERE IT IS THE BELT. MIKE
Pop off lite cover unscrew two screws ,pull off rubber cover around base push screwdriver in slots on sides pop off base
Repair Help & Product Troubleshooting for Kenmore 23313 Whispertone Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I cannot get the Kenmore power-mate open to change the belt? How does it come apart?


... Kenmore Vacuums

Change the belt in my kenmore power-mate 120 amps...how to open it to get to where the belt is???


HELLO, JUST REPLACED THE BELT ON OUR'S. FIRST TAKE LITE LENSE OFF THERE WILL BE 2 SCREWS, REMOVE. THEN FLIP OVER POWER MITEON EACH SIDE PRY WITH 2 SCREW DRIVERS WHERE THE ARROWS ARE TO SEPERATE & THERE IT IS THE BELT. MIKE ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Chang the belt in my kenmore power mate power head


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Change belt How do I open the power head to get to the belt to change it?


... Beam Rugmaster Plus Belt

How do I change the belt on the side. Have a Bissell Power Lifter. The belt broke and i cannot get it changed. HOW do I change it?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Kenmore elegance: how do I open it up to change the belt?


A picture is worth a thousand words, so the diagrams in this manual should be helpful:..35622 Owner Manual ... Vacuums

Power mate 116.51513001 on whupertone 116.21513001. How do I open Power mate to get at the inside?


... Kenmore 21513 Vacuum

My kenmore model no 116.22512200 canister vacuum power head has no suction & doesn't pick up even though it shows all the signs that it is getting power. The junior power mate works fine.


... Kenmore Vacuums

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Need to replace belt in Kenmore Vacuum Power-mate nozzle


Hello,\015\012\015\012Here's what you'll need to replace a belt on a Kenmore canister vacuum:\015\012\015\012- Phillips Head Screw Driver\015\012- Flat Head Screw Driver\015\012\015\012There are two different ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

The power head of my 1165581590C Kenmore Power mate Whispertone 12 amp vacuum won't open. It is an older model and it desparately needs a clean!


I am not 100% sure of the model number but most of their powerheads come apart quite easily if you know how. There is a light lens cover on the top of your powerhead. On each side of this cover there is a little clip that holds it in place. You ca ... Vacuums

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?


Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Need to change belt on hoover upright model u5093-900, but can't figure out how to open it up to get at the belt.


... Hoover Vacuums

I have a kenmore vacuum cleaner that I bought a new belt for butcannot get the bottom off to change the belt. Model # 116 53312305


... Kenmore Vacuums

I have a kenmore Model # 116 22100400 about 6 yrs old and I can not get any power to the machine, I was using it and it stopped and will not go anymore. I have changed the bag, checked and cleaned the filter and no power when plugging the machine in and turning the button on.


... Vacuums

How to open the head on a kenmore power-mate 116 52251502C


... Kenmore Vacuums

The brush on my hayden 6000 supervac is not rotating when power is on and i can't figure out how to open the vac to get to the belt. help please


First you will want to remove the light cover. this can be done by pusing as you look at the front of the powerbrush on both the left and right side of the head. There you will find the lightbulb and 2 screws to remove. Remove both of the screw ... Hayden Industries SuperVac 6000 Central System Vacuum

Trying to change belt in kenmore 3116890 upright vacuum cleaner model116. Can't open vac


... Kenmore Vacuums

I have an eureka power plus vacuum floor cleaner and i have no way of opening the botton to the brush to change my belt for the brush since the brush will not turn.


Look for two screws at the edge of the brush housing. You may see these ones on top. They will be black and recessed ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Can't get at the belt, on my DC41, to change it. How do you open the housing?


This video will help you ... Dyson Vacuums

How do i open my vax power 5 to change the belt for rotateing brushes


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Need manual for kenmore power mate model No. 116. Need to know how to replace belt.


If you're talking about the belt that drives the brush in the power "head," you can replace it without the help of a manual. I did, and I'm certainly no mechanic. --Mike T ... Vacuums

MY hooverselfproweled windtonel sound like an air craft getting ready to take off and lost alot of sucking powers. I had it serviced at a local store. It wasn't right when go it back. All belts and filters where changed.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=761558\015\012Generic problem for all Vacuums\015\012MY Hoover self propelled WindTunnel sound like\015\012 ... Vacuums

HOW DO YOU CHANGE BELT CANT SEEM TO REMOVE BOTTOM TO GET TO IT KENMORE WISPERTONE 116


The top cover to the light lense pops off at the ends. When you get that cover off then you will see 2 screws that are by the swivel neck. Take those out and then the whole body top cover comes off. That will get you into the roller brush and belt ... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1238 seconds