Having problems with your Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum ?

Kenmore PowerMate cannister: Reattach cannister floor piece.

\015 Mine is not this exactly but an older model. There is a metal low/med/high level-raising piece on the bottom of the floor attachment that came out. I need to reattach it but how to get it in so it lies flat again? I can get the middle part snapped in but the ends don't fit back in like they were before. HELP! Thanks!\015

Answers :

You need to open the head by gently squeezing the light cover housing and lifting it off. There will be two screws underneath and once removed the lid will lift off and reveal the area where the pedal installs.
How do you remove the cover from the sweeper to replace the bely?
Repair Help & Product Troubleshooting for Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore PowerMate cannister: Reattach cannister floor piece.


You need to open the head by gently squeezing the light cover housing and lifting it off. There will be two screws underneath and once removed the lid will lift off and reveal the area where the pedal installs. ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Kenmore Progressive Cannister Vacumm, Powermate Floor Unit quit working. I replaced the reset switch but still nothing. Light doesn't work either.


Is it working on other mode?.Or its not having any power at all?.\015\012\015\012Select a switch position o the handle.OFF MODE.\015\012\015\012FLOOR:-- turns on the canister motor only. \015\012CARPET :-- turns on both the canister and the Power ma ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore cannister vacuum tube - reattaching connectors


Make sure that the two prongs that go over the hose are going in the correct slot in the cuff. If in the wrong one, the cuff won't snap into place. I have had to slam the end of the hose on the work bench while holding the cuff to push it all of th ... Kenmore 22822 Canister Vacuum

Works in FLOOR position but not in CARPET. - Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum


The power nozzle has a reset button. Push that and that should fix the issue. You could of sucked up the corner of a piece of carpet causing the brush roller to become jammed. If that doesn't work, there could be a problem with the hose. The hose per ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Need manual I am in need of the owners manual for a kenmore cannister with powermate model #116.2140090


... Vacuums

Kenmore canister model numer 26212690 12.0 amps with powermate. How do you remove the bottom part to check the belt. The blade won't turn and the switich is on rug not wood floor. There are two arrows that say to seperate use screwdriver at arrow. Have seperated at the arrows but the back will not come apart.


Hi There,\015\012\015\012There are actually two screws that need to be removed before you can separate the bottom from the top housing. The screws are actually located either underneath of the headlight cover, or on the bottom of the ma ... Kenmore Vacuums

Kenmore model 116.21614 shuts off when floor cleaner is attached. works ok with powermate attachment but with poor suction


... Kenmore Vacuums

Why doesn't my vacumm floor piece work? - Kenmore Vacuums


Not sure which unit you have but normal repairs would be to the wiring of the floor fixture and to check to see that the beater brush is turning properly.\015\012If the brush is not turning it could be a broken belt or the fact that the beater brush ... Kenmore Vacuums

Sears progression kenmore canister va. Model 11623612300 on the wand, the plastic piece broke off, there is one long wand with two piece to it well the plastic piece, not on the bottom, where it hooks into the beater bar thing, but the other plastic in the middle. Can this be replaces?


Hi.The part is probably available as replacement.Please click here ... Kenmore Vacuums

I have a new Euro-Pro shark model S3101. Used it one time and while I was doing my tile floor in my kitchen I reached under a cabnet to clean and hit the floor kick kind of hard and broke the head off of the shark. I have only the T shaped end on the shark now with the cleaning head broken off and looks unrepairable. I did kind of hit the floor kick hard but the plastic broke like glass. Can I put a new head on the remaining piece or is it repairable? thanks Angie


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Pro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

I have an older kenmore canister powermate 3.9 and the vacuum itself works fine but the powermate isn't sucking after a toy was sucked up last week. The toy is out but the powermate doesn't work. I assuming that is what it is called. The big long part that hooks to the canister that actually cleans the carpet. I would appreciate any help.


... Kenmore 25512/ 25513 Progressive Canister Vacuum

DC-17 - Reattaching the U-Bend piece in the back of the machine


On the back of the machine you will see 2 guides where the peice should just slide easily check for dust ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kenmore Progressive Model 116 35922500 - bottom piece back on?


... Kenmore Vacuums

Need Hoover cannister vacuum floor brush & filter bags


Yes attachment are available just bring your wand into your local vacuum store to insure the proper fit ... Vacuums

I have a Hoover Elite Rewind vacuum. Actually,this is my second one. However, after about 4 months of use, it emits a "sour" smell when I'm using it. I empty the cannister before each use and clean out the filter monthly. My house has mainly hardwood floors, so I typically only use it on area rugs and 2 small carpeted rooms. Is there any way that I can get rid of the smell? I've tried putting a dryer sheet in the cannister, but this gets stuck in the filter mechanism. Also, carpet fresh clogs th


Does it smell like an electrical burning odor? could very possibly be the motor going bad already. ive seen it happen. but if not try freshwave odor absorbing pearls. i carry it in my store and we do have shipping. Truly the only thing you should use ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

The steam is comming off the tip of the body but the attached floor piece will not let the steam out to the floor through the pad. The body tip has turned white because of the steam pressure build up.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.


You don't have to take the vacuum apart.\015\012Assuming this is an Epic 3500 or similar upright Electrolux:\015\0121. Lay vacuum on it's side.\015\0122. Gently pull hose from power head. It's not screwed in so that should be eas ... Electrolux Epic 3500 Vacuum

We have a Kenmore canister vacuum cleaner and the power in the floor component (rotating brush, etc) is no longer functioning. The vacuum is producing suction, but does not seem to be providing power to the floor component.


The problem could be with the power head itself or the hose providing the power. If you can turn the unit on from the handle, then its not the hose and you need to get a new power head.. ... Panasonic Kenmore Canister Vacuum Vacuum

HI, I have a Kenmore 25813 and it seems like there is an intermittent short. When I have the extension wand on and the power floor attachment on, when it rotate the wand the light cuts out and so does the power floor attachment, when I twist it back it comes on again. I don't have this problem if I remove the wand and just use the crevice tool with the hose. Any idea where the short might be and can I fix it myself? Thanks. Gary


This is common you may have a short in the contacts from the handle to the wand or a break in the cord that goes into the powerhead ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

Needed, a new Hose for Kenmore Canister Vacuum cleaner. Model Number 1162497184 --A 3.9 Powermate Kenmore Vacuum Cleaner


... Kenmore Vacuums

Where is fuse kenmore canister vacuum - Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

The motor in my Powermate (Kenmore Canister 116.27614700) is whining, high pitched, but still works. A local shop told me the motor is dying (the one in the Powermate that drives the beater bar) and would cost $150 for them to repair. The machine is only 1.5 years old and I paid $300...yikes. I think I can fix it but don't understand why the foam gasket that apparently wraps around the motor costs as much as the motor. This is assuming that part 32 (ks747156) is the foam I see glued to my cur


I think you are right! Buy the motor.....use the gasket from the old motor if you can cut it off clean and just glue it on the new one.\015\012\015\012The connectors are just brass blade connectors which you should be able to get at a Ho ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

How do I use kenmore evo carpet cleaner? - Kenmore EVO All Surface Floor Cleaner Vacuum


Lost instruction on how to use kenmore evo carpet cleaner ... Kenmore EVO All Surface Floor Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0500 seconds