Having problems with your Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum ?

Light bulb burning out.

\015 Bulb burned out on the wand of the canister model..ordered 3 aftermarket bulbs (none listed on the Sears parts list), after replacing the bulb, the new one burned out after 1 or 2 minutes of use. Replaced the bulb again, it got bright then burned out after about 2 seconds. Could there be a power surge to the circuit, and how do I fix it?\015

Answers :

My guess is you didnt get the correct value lamp for your application. Sears doesnt have the proper lamp for your machine - of you didnt want to get it from them?
\015\012
\015\012Try again at Sears or RepairClinic.com for the proper lamp.
\015\012
\015\012I hope this helps you
\015\012
\015\012a
\015\012
Repair Help & Product Troubleshooting for Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Light bulb burning out.


My guess is you didnt get the correct value lamp for your application. Sears doesnt have the proper lamp for your machine - of you didnt want to get it from them?\015\012\015\012Try again at Sears or RepairClinic.com for the proper lamp. ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I have to replace the light bulb and can't find the instructions in the manual. I guess they figure it's obvious, but not to me! I've had it for about 30 years and can't remember the bulb burning out before. I have the replacement, just need to know how to do it.


Hi,What make and model vacuum do you have?Thanks,Handie Andie ... Vacuums

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

On the kenmore progressive canister model 116-25614504. What causes it to keep burning out the bulb?


... Vacuums

Light bulb change on Lux 4000 upright, light at base piece infront of spinning brush, made to look like long thin bulb due to plastic covering, how to open to change bulb 15 watt


... Electrolux Vacuums

I have a light ballast that stopped working. The lights around this one bulb still work but changing the light bulb did not fix the problem. Any idea what is going on here?


The ballast is like a fuse and the ballast is blown .\015\012you will need to replace the ballast as it will let current thru for some bulbs but not enough to light them all up.\015\012also if you use old bulbs that are alomst blown and n ... Vacuums

Have Hoover Concept vac. Both bulbs burned out. What is wattage for new bulbs? They are 912 bulbs, but don't state watts.


... Hoover U8315960 Bagged Upright Vacuum

I have a coralife aqualight model 53008. It uses two 65watt compact bulbs. The whole light quit working one day. I tested the bulbs in another aqualight I have and the bulbs were fine. I want to know where the ballast is. I opened up the ends and the wires are so secure I cannot pull on them to locate a ballast. Please advise if this is a ballast problem and how do I replace it. Thanks Linda


... Vacuums

I have a ceiling light with a holgen bulb that I cannot figure out how to change. The fixture has an outer ring against the ceiling and an inner ring that has the light. The inner ring tilts. I have not idea how to get into it to change the light!


From what I know you are suppose to change the whole thing. ... Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum

Pfaff Sewing Machine - Model 0100A - How do you repalce the light bulb please? Does the side of the machine open somewhere to get access to replace the bulb? I have got the blown bulb out by squeezing my fingers up, but can not get the new one in securely.


... Vacuums

Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???


Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I bought a ceiling fan from lowe's, got it home got ceiling fan up in the bathroom, when we put in the light one of the halogen bulbs does not work , also two of the cobalt blue glass covers are cracked all the way through and one of the halogen light protectors also had a whole in the end of it. I called Lowe's they told me to contact you; day of purchase was 3/1/08 in Florence Al. store code # 04810-30108. Ceiling fan bar code 0 2403478512 2. 228365 52" Helix Chrome and Cobolt ceiling fa


If this is a new product and it is defective, take it back to Lowe's and insist on a replacement, talk to the manager if you have to. This site will only advise you on how to fix it. ... Vacuums

I have a ge light switch receiver rf1023, with incandescent bulbs, and when I try to switch it on it just blinks once and goes out. if I hold the switch on the battery-operated wall remote, the lights keep blinking until I let go. It used to work fine, and now it doesn't. I've lost the intallation instructions, so I don't know if there was a trouble-shooting section that covered the problem.


... GE Vacuums

I have a Smithsonian, 80x Mega Screen Microscope, Item #1143 in which the light bulb has ceased working. Where can I purchase a new bulb, 4v 0.3A.? I live in Australia


... Vacuums

I put brand new T8 light bulbs in a fixture but the lights are still flickering is it the ballast.


Are they actually flickering on and off?- or just sort of Twirling patterns of lighter and darker shade of light? -- That is normal when the bulbs are new-- That should become steady in a few days.If not-- tell us more what is happening ... Vacuums

Sylvania 25134 F96T12/CW/HO/COLD TEMP Straight T12 Fluorescent Tube Light Bulb Whats exactly is meant by "cold temp"? And when we have just 1 bulb in the socket, its end will glow. But when we insert the other one, it doesn't glow anymore, and neither one of them work. Any help would be appriciated! Darren


... Vacuums

My bug zapper bulb has burned out. it is the lentek FT24G-MX. Can you tell me where i can get another bulb? thank you, myrna stancliff


... Vacuums

I have a Hampton Bay ceiling fan model #EC2T-36 HPF. We broke the globe that covers the light bulb when we were changing the bulb. Just wondering if you could tell me where I can buy a new globe cover?


... Vacuums

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.


It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

I have a GEelectric percolator from about 1955. It looks like a pot belly stove, or an egg standing upright! It works fine, except the little red light that normally comes on when the brewing is completed no longer lights. I assume it is the bulb......but how do I get to it? It is located near the coffee brew setting mild-to-strong sliding lever.


Hello Theodore.I also use a coffee pot similar to yours. Makes a great pot of coffee.While I have never had to replace mine I have had these type apart years ago.It probably has a 120V neon style bulb soldered into the circuit mount ... Vacuums

Zephyr 24 bulb tanning bed. How do I get into it to change a ballest? Four bulbs are not burning in the backside two top and two bottom.


... Vacuums

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down


... Eureka Vacuums

I have a halogen light bulb with a frosted glass cover over it. How do I remove the cover to change the bulb?


... Vacuums

Replace light bulb on oreck xl 21


... Oreck XL21 Bagged Upright Vacuum

Change light bulb


Ok just like you would change the belt take screws out of top the cover should come off inside there is a plastic cover take it off theres the bulb ... Kenmore 25512/ 25513 Progressive Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0288 seconds