Having problems with your Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum ?

Wheel is sticking. I want to remove the wheel to clean the axel. kenmore 116.27514700


Answers :

Hi,
\015\012
\015\012Thanks for the clarification. This is actually fairly simple to remove the rear wheel, however as you'll see after this has been removed, there really is no axle attached to this. It just snaps into the main canister housing. It may be that your wheel has broken, and a new wheel may fix your problem.
\015\012
\015\012First here's a link to the parts shematic for your model so you can follow along:
\015\012http://www.searspartsdirect.com/partsdirect/getSubComp.pd?modelNumber=11627514700&productCategoryId=0642000&brandId=0582&brandDescription=KENMORE&modelName=VACUUM-CLEANER&diagramPageId=00001&componentDescription=CANISTER&documentId=P0706048&blt=06
\015\012
\015\012Simply put a flat head screw driver behind the brush, and pry it off. It will easily come right off. You may inspect the wheel, and the wheel housing that it snaps into to make sure there are no obstructions, or pet hair that are slowing the wheel down. Also look at the clips that hold the wheel in place to make sure there's no debris above the clips on the wheel that could slow down the brushes also.
\015\012
\015\012If it all appears to be fine, you may spray some WD40 on the part of the wheel that spins, reinsert it back in the vacuum cleaner and test to see if that fixes it. If it didn't, you might just want to purchase a new wheel assembly.
\015\012
\015\012Here's a link to the rear wheel for Kenmore canisters if you'd like to purchase a new one from our website:
\015\012http://www.govacuum.com/kenmore-panasonic-canister-rear-wheel-assembly-panasonic-part-ac99caktzv07-sears-part-4370702.html
\015\012
\015\012Hopefully that helps you. If you have any questions about how to repair this, or other questions that I did not address, simply just add a comment as you did last time, and I'll be more then happy to answer any and all of your follow up questions.
\015\012
\015\012If you found this repair helpful, please be so kind and rate my repair, or leave feedback. This is really appreciated, and one of the reasons that Fixya repair professionals continue to post free repair advice on Fixya.
\015\012
\015\012Chris Jones
\015\012GoVacuum.com
Repair Help & Product Troubleshooting for Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wheel is sticking. I want to remove the wheel to clean the axel. kenmore 116.27514700


Hi,\015\012\015\012Thanks for the clarification. This is actually fairly simple to remove the rear wheel, however as you'll see after this has been removed, there really is no axle attached to this. It just snaps into the main canister ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Both of the wheels are wobbly and loose on my Kenmore upright vacuum model 721.37060. I don't see where I can remove them to analyze and fix the problem, which seems to be that the wheels are loose on their axels. How do I get the wheels off and what do you think I'll find inside?


Most if not all vacuums have an access panel on the bottom.It may be held on by a couple of big plastic clips,the kind you squeeze together and it releases a door.Some have plastic screws.There may also be a couple of phillips screws along with it or ... Kenmore Vacuums

Electrolux 6985A wheel (the one on the cord side) is sticking. How do I remove it to clean out the hair or whatever is making it stick?


Most of these wheels have a push fit. the larger the diameter the tougher to reach the axle portion, but it generally has a flex cutout on at least one side which you can push in slighlty with a long flat screwdriver. Try spraying with WD 40 or silic ... Vacuums

The caster wheel on my Kenmore canister vacuum seems to be sticking. It's not wanting to turn when I pull it. When I flip it over and look at it, though, it seems to spin okay


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Kenmore Quick Clean - how to remove dirt from cannister


This is the web site for Kenmore owners manuals--->http://www.managemyhome.com/mmh/<---Please take the time to give this solution a fix ya ra ... Kenmore Quick Clean 30012 Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)


I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

I have a bissell proheat 2x and it leaks water around the wheel it holds dirty water but doesnt hold clean water.......and how do i remove the wheel on my bissell


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.


Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Cleaning Filter Hi: I want to clean the filter on the B&D pet hepa vacuum, but can't figure out how to take it out of its housing. I can remove the housing from the actual vacuum, but don't know how to get the filter itself out. It sure does smell of dog, so any help would be appreciated.


... Black & Decker Black Decker Bagless Canister Pet VacVacuum

Have Hoover SteamVac Model F5835-900. Has gunk under the front clear hood where water/debris is lifted from carpet to the tank. Wife wants me to remove clear hood to clean; however the hood cannot come off without damage. Can I safely remove this hood?


There 2 screws on the bottom edge, one on each side, then there is a ***** on top at just beyond the lip of the window. Then it will come off of the machine. \015\012\015\012 ... Vacuums

Hi my beater bars will not turn anymore, i have tried to reset it cleaned the bars removed and cleaned the front wheel, but still they will not turn.Any help would be appreciated


Belt has probably broke in the power head ... Vacuums

I want to clean fluff from underneath the transparent front panel of my Bissell 11 7901. I have removed the screws from the bottom of the panel, but it remains firmly in place. I do not want to apply apply forceful leverage in case there is something else that needs to be done before the panel will come off. Any suggestions, please? Peter


I just did this one myself, You've done most of the hard work already.Be sure your holding tank is out and not in the way.Double check the down front screws are still out since you sent in you question. Now tweak the front section (the business end) ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The rear wheels won't stay on my Kenmore Progressive 359235 Upright with Inteli-Clean Vacuum


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?


... Bissell Vacuums

My kenmore power spin shampooer's brushes do not spin and how do I clean those brushes . Can they be removed?


... Kenmore 85930 PowerSpin Deluxe Upright Wet/Dry Vacuum

I have a DC 15 Dyson Ball Vacuum. I've removed and cleaned the filter. I can't get the lid to close properly. I don't want to force it and break something. There is some kind of a red spring loaded tab that seems to be in the way. How do I reseal the top of the vacuum?


The red tab doesn't let the lid close if the filter is not fitted correctly or the wrong filter is fitted. Many after-market filters cause this problem. \015\012\015\012Have you recently fitted a new after-market filter? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Kenmore bagless 116.36932502 the interior filter port fills up very quickly-withih minutes of initial startup-- and has to be removed and cleaned constantly. Debris backs up into the interior of the main filter as well, the main canister never gets full. New problem with old machine!


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

How do you remove the back wheels from a Kenmore Model 116.2441290 canister vacuum cleaner? Do they just pry off?


... Kenmore Vacuums

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.


The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

Squeaky wheel I don't want to take apart more than I have to. The front cover has been removed and I tried using WD40 on the squeaky areas but the problem has not been resolved.


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1161 seconds