Having problems with your Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum ?
Remove connectors off hose
\015 Kenmore Power Mate 11627212790 How do you pop off connectors without breaking them. Should it be this difficult?\015
Are you talking about the hose cuffs? If so, put the cuff in a vise and squeeze it until you see the locking tabs and using flat blades, pry the hose out from the cuff.
Repair Help & Product Troubleshooting for Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have some sort of object in the hose of my Epic 6500. I have tried reversing the hose and blowing out the foreighn piece of debeis but this has not worked. Is there a way to remove the plastic connector end to access this end of the hose? Or is there another solution to this problem?
By reversing it, I assume you plugged the hose into the exhaust blower on the top of the machine. If so, insert the other end into the intake and turn one the vacuum. This way the clog is also getting sucked at what should be the loose end.\0 ... Electrolux Epic 6500 Vacuum
The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!
Great. ... Kenmore Vacuums
Remove connectors off hose
Are you talking about the hose cuffs? If so, put the cuff in a vise and squeeze it until you see the locking tabs and using flat blades, pry the hose out from the cuff.\015\012 ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak
... Kenmore Progressive 35922 Bagged Upright Vacuum
I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?
I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums
Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg
Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums
Can you remove the plastic hose that leads to the handle as mine has split. I thought i could remove it by pushing in the two black bits of plastic then shorten the hose. so far it wont budge. Is it meant to as Dyson sell the whole thing in one? cheers john
Yeah sorry it is sold as a complete unit and its a real pain to strip down so it better and faster to just buy the whole thing from dysons website ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron
The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum
I want to remove the hose from the handle of the vacuum? I already removed the plastic clip. I thought that would free the hose, but it did not. Any ideas?
There are two discs on top on the dandel that cover the screws. You need to remove the two screws and the you can take the handle off the hose.\015\012\015\012Bob\015\012 ... Electrolux Centralux Vacuum
My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit - Centralux central vacuum system. Where can I find a diagram of how to remove the handle?
Do Not Cut the hose! It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applic ... Electrolux Centralux Vacuum
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
When you remove the hose to use the utensils, the dirt is flying out of the hose at the bottom where the utensil is removed from
Hi Karen. I understand how frustrating this can be. Dust blowing from the bottom hose is normal because the brush is still rotating. If there's excessive dirt flying out, then you may have a clog in the bottom hose. \015\012Here's a quick link to ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum
Clogged hose... I have a clog in my hose, probably a sock, I have pushed it through to the hard plastic handle end of the hose, help! can the plastic handle wand be disconnected from the hose to remove the clog??? Thank you
Hi!\015\012 \015\012Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Con ... Bissell 6594 PowerForce Bagless Upright Vacuum
EuroPro EP961 - Is there a way to remove the hose for cleaning?. It produces steam but no steam come through the hose. Thanks
... Euro-Pro EP961 Steam Vacuum
I want to install a new hose on a Sears vacuum Mod #116.23812300. How do I remove the Hose Connection Cover(#4370325)? It appears to be a flexible plastic part, however, it will not move from it's position on the old hose.
Hi,\015\012\015\012Please CLICK HERE \015\012This guide will explain you how to replace the hose.\015\012\015\012Goodluck.. ... Vacuums
I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth
When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums
The red light comes on when the bag is not full (in fact I put in a new one). When the hose is removed, the light goes off. How do I clean the small hose that leads to the bottom of the vacuum and the main hose?
If it has a clog caused by a hair ball or some other object, a "properly bent" coat hanger can be used to fish it out. ... Vacuums
I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!
... Miele Vacuums
I have a Hoover 5899-100 Steamvac. The hose is cracked at the bottom. I am going to order a replacement hose, but can't figure out how to remove the old hose. are there instructions out there to do this.
DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each
Should be a pry off dot on the underside revealing a screw ... Vacuums
I have an Aerus Guardian canister vacuum with a clogged hose. The tiny stuffed animal toy is lodged right below where the swivel handle meets the hose. Switching the air flow does not dislodge it. I would like to remove the handle from the hose. Any suggestions?
Consider this. If your vacuum is still under warranty, removing the hose will void the warranty on the hose. I strongly recommend calling an authorized dealer/consultant.\012Although it may seem to be fairly simple to remove the handle, there ... Electrolux Guardian Bagged Canister Vacuum
How to I remove the hose from the base of the bissell spot clean pro to remove a clog.
Dont no if this one is the same ,but it may help you, click the link belowhttp://www.youtube.com/watch?feature=player_embedded&v=1sSVIu6arbY#! ... Bissell Spot Clean Pro Portable Deep Cleaner Professional Spot Cleaner
Hose is clogged, can't remove hose.
Hello,i have a 2996AVS,i have worked on many vacuums like this,if you look down on the top cover where the wheel height knob is,on the far left & far right side's there is a chrome phillips head screw on each side,remove these two screws,the top ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Bissell Spotbot hose needs removed and cleaned
H3000 recovery hose broke. How do I remove the
You can find a link to the schematic below. The schematic points out where all the screws are on the H3000. You can also find any parts that you need to replace. ... Hoover Floormate H3000 Upright Wet/Dry Vacuum