Having problems with your Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum ?

Cant open roller assembly roller not spinning i dont see anything in the way

Answers :

Turn\015\012 the power head over so the bottom is facing up. On the bottom towards \015\012the back there are two holes (one on each side) where you can get to the\015\012 access screws. Remove the two screws (you'll need a phillips \015\012screwdriver). With the screws removed you can now remove the top cover \015\012from the base by pulling out on the two clips on each side of the power \015\012head. With the top cover removed you can get to the belt and roller \015\012brush. If you need a belt for this model you can get it here:


Don't forget to rate the answer!
Repair Help & Product Troubleshooting for Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cant open roller assembly roller not spinning i dont see anything in the way

Turn\015\012 the power head over so the bottom is facing up. On the bottom towards \015\012the back there are two holes (one on each side) where you can get to the\015\012 access screws. Remove the two screws (you'll need a phillips \015\012scr ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

Motor still runs--sounds like jet engine. do I need a new motor? or is there some sort of muffler that has malfunctioned? vacuum belongs to disabled mom---so trying to do work ourselves--cant afford much. dont see anything obviously wrong--but know nothing about electric motors.

This little vac I think is actually made by Samsung. If it is ROARING and vibrating, either the bearings or suction fan is in bad shape. Remove the lid as if to inspect the belt and see if there is a visible intake opening with a plastic fan rotatin ... Bissell 3590 CleanView Bagless Upright Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

I have a raynor flight star garage opener. Had a lighting strike 4 days ago. All power is good. The opener even has a little green light on the switch that is attached to it. However the opener is not responding. Is there a way to reset on the motor by taking off the housing? I don't see any reset button on the out side of the housing.thnx w

You could always try unplugging the unit and plugging it back in. If that doesn't work the logic board is probably fried and unfortunately there is no replacement available for it any longer. You would need to buy a new opener. I'd recommend Liftm ... Vacuums

My steam mop gets hot but steam is not coming out when i pump it. However when I release the bottom attachment steam comes out of bottom of the base (purple part). I took the attachment off to see if it was plugged but dont see anything. Any suggestions?

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.

... Hoover Vacuums

I shorted out the light socket on my Chamberlain Professional Garage Door opener. Now it wont open, I am looking for a fuse or reset button, but cant find one. Is there a way to reset it or did I fry the solinoid

First check your house fuse. ... Vacuums

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a

... Electrolux Vacuums

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!

The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums

How can I change the belt on the kirby vacuum shampooer brush roller. There is no way to snap the roller out and it seems that trying to unscrew the end isn't doing anything either.Model 5584 renovation group is what is written on the shampooer attachment. The kirby is a heritage model 2HD - purchased in the late 1980's.

... Kirby G6 Bagged Upright Vacuum

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy

The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

We have a dyson vaccume and what ever makes it stand isnt working. I dont think we did anything wrong. But I cant make it stand.

The steel rod has come out of the groove that makes it go up/bown this video will show you. ... Dyson Vacuums

I got a rubber Dog toy jammed in the roller...**giggles** How do I open the roller area to get it out :)

... Kenmore 23513 Progressive Bagged Canister Vacuum

I have a bissell proheat clearview plus steamcleaner. i was using it and then the little red flow indicator stopped spinning and it quit sprayng any liquid. i looked for where it could be clogged but i dont see anything

Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Can I open the vacuum to see what could be blocking the roller from rolling

First of all disconnect the electrical power supply and then remove the lower plate that holds the brush rollers. You should now be able to slide out the brush rollers.\015\012Hope it helps and comment if you need more clarification.\015\012Best ... Vacuums

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.

Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

I have a Dirt Devil Featherlite Model 085430. It making a horrible noise and I want to open it up to see if anything is broken or lodged in the motor housing. I've removed all the screws I can find and still can't get the thing apart.

Hi,\015\012\015\012The user manuals in this site may be helpful.\015\012\015\012Best wishes. ... Vacuums

The roller brush at the bottom of the vacuum is not spinning, hence it isn't picking up the dirt. I am unable to find a way to access it so that I can see what is stopping it from turning. Can you help me?

Hello. uUsually when the roller brush stops spinning the belt is broken. TIp the machine upside down and look for several screws which hold the bottom together. Mark the location of each screw when you remove it as different lengths are common and ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

The hose line leading out from the roller compartment is clogged and I can't access it to clean it out. How can I clean out that portion of the hose. I am assuming this is the problem because I can see it is full and the bag is not filling with anything.

If you have access to a short "snake" for cleaning sink drains, this could solve the problem for you.\015\012Use is manually to insert into the hose and carefully work it around to see if you can clear the clog this way. ... Vacuums

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help

Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help

Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

There is no suction, hoses do not appear to be clogged, is there a way to remove the piece underneath to see if there is anything clogged there

The top cover to the housing comes off in order to get to the roller brush area to check for clogs. There are two screws in the back of this cover to take out and then the cover will come off. ... Euro-Pro NV31 Infinity Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0458 seconds