Having problems with your Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum ?

I have a kemore progressive canister vacuum and the power head connects enough to the hose where the head accnoledges it's connected and the brush spins BUT i can't get it to lock in so i have

Answers :

Repair Help & Product Troubleshooting for Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kemore progressive canister vacuum and the power head connects enough to the hose where the head accnoledges it's connected and the brush spins BUT i can't get it to lock in so i have

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I can't get the latch that connects to the brush head to engage. Thus the vacumn is extremely hard to push. It has suction, extreme suction. Rollers appear to be dragging. I've tried to remove and reinstall the head several times but cannot seem to get the latch to engage. Please advise.

It sounds like something has come out of it's socket. If the brushroll won't turn rapidly, your clutch is worn out ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.

I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Dyson DC28 works fine for a minute then it's like if the brush head gets too much resistance it quits spinning and the light starts flashing. When I turn the vacumn off then back on it's f

Hi Gayle,I'm sorry to hear you're having difficulties with your DC28. From what you've described, it sounds as if you may have the brushbar set at a level too low for the type of carpeting you're cleaning. If you select a higher carpet settin ... Dyson DC28 Animal Bagless Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Lost the cap that locks the brush in place on my dc35. Can't use it until I can get another one or find out where to purchase a new head.

Try this link below for your parthttp://www.vacpartswarehouse.com/Dyson-DC35-Handheld-s/3899.htm ... Dyson DC35 Handheld Vacuum

I've had my Kenmore Progressive canister for at least several years and never had a problem. Now, the carpet head brush does not rotate, it's not getting the connection unless I push down maintaining pressure on the handle.

Hi, try pushing the reset button with a pen or paper clip. If that doesn't work, the motor may need to replaced. If the reset button is stuck, if the reset button is stuck, use a pair of tweezers to pull it back out......\01 ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I cant get the brushes to spin on my hoover max extract carpet cleaner

Remove the brush assembly and insert a flat screwdriver into the square hole and be sure it turns. If it is seized up, the turbine assembly will require replacement. If it turns, be sure the brush control is set to the brush position and the filter i ... Hoover Vacuums

Hi, i have a hoover steam vac agilty. the brushes on the bottom front quit spinning. they are not locked up as i can freely turn them by fingers. is there a belt that i need to replace? if so, how do i get at it to replacec it? thank you for any assistance

The brushes on all hoover steam vacs are air opperated it uses the suction of the vacuum motor to spin a turbine and in turn spin the brushes. Most likely that path of air is clogged with hair or carpet fuzz. On the top of the machine there is a litt ... Hoover Vacuums

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.

Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???

... Vacuums

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition

Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

The brushes on my Hoover Steamvac Widepath LS SpinScrub model # F6040 900 are not spinning. What should I do to get the brushes spinning again?

On those models the brushes are turned by suction. 1. Check the lower tank to be sure its completely closed and sealed.2. Check the lower tank to be sure the tools filler plate is in place (if you used the tools recently)3. If both 1& ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Dyson DC22 brush wont spin, does not appear to be getting power

Hi there,I'm sorry to hear you're having difficulties with your DC22. If you've been unable to get the Motorhead working after cleaning it, please get in touch with us directly so we can provide further assistance. You can call us free on 1-8 ... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

Brush head not spinning

Remove brush from vacum, remove ends of brush, clean... ... Vacuums

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t

... Vacuums

I have lost the cap that locks the brush in the motorized head. I didn't realize it was gone until I went to use it. Can I purchase the locking cap or can I buy a new motorized head for it. I lov

If this part is for a Dyson vacuum here is the link:http://www.dyson.com/parts.aspx?gclid=CJShrcD99rQCFYKK4AodBDwA7g ... Dyson DC35 Handheld Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?

Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brushes have stopped spinning,how do i get them to spin again on my dyson slim? We have tried the brush button

One possible problem could be a worn clutch. I just had the same problem. Before buying a new clutch assembly, I took the out the clutch just to make sure I could do it (the link previously mentioned is great: ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

I have a steam cleaner and i can not get the black arm brush to keep one side up and when you trun on the steam cleaner the brush dose not spin when you start to clean the floor but it will spin when you have it siting up right

Sounds like you could have an elevator broken (part #2000010). You will have to take the top off to replace them or to check to see if one of them is broke. There is one on each side so when the handle is in the upright, they push againsy the brush ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.

The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Miele White Star SEB 204, powerhead stopped spinning. brushes are clear of debris, belt (#3854940) is not broken. Could belt be stretched so that brush head does not spin?

Yes, most likely the belt has stretch. Flat belts do this after a short time and need to be replaced when problems start with the brush roll not wanting to turn. Also check the brush roll, make sure that the ends turn freely, if not, then replace i ... Miele Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1167 seconds