Having problems with your Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum ?

Broken vacuum jammed the rotating brush on a kenmore powermate vacuum cant get it to run properly after clearing the jam

Answers :

Question; you can't run it properly meaning? The agitator (brush) isn't spinning? If that's the case, then Kazong is right, check the belt. If the belt is fine, check to make sure you didn't damage the bearing of the agitator.
\015\012How to get to the agitator/belt:
\015\012Remove the 2 screws that are holding the cover into place. Usually found on the bottom of the power head; in some cases, they are found on the top of the cover. Detach the cover from the back and the sides.
Check the belt it may have broke or stretched out
Repair Help & Product Troubleshooting for Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Broken vacuum jammed the rotating brush on a kenmore powermate vacuum cant get it to run properly after clearing the jam

Question; you can't run it properly meaning? The agitator (brush) isn't spinning? If that's the case, then Kazong is right, check the belt. If the belt is fine, check to make sure you didn't damage the bearing of the agitator.\015\012\015 ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

Hoover windtunnel motor is running rough and overheating, even after clearing the hoses and removing the belts. Could there be something jammed in the blower? How do I get in there to clean it out?

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How do I open my kenmore powermate vacuum (model # 116. 22100400C)to get at the motor?It's making a loud noise when running.

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I bought a Bissell Poweredge Pet vacuum from target. There were no boxed products so I took it off the shelf. The instructions are in the clear filter, but I can't get the vacuum to release and let me get the instructions. How do I ge the instruction pamphlet out of the clear filter portion of the vacuum?

Hi,If you go to this website, http://www.bissell.com/poweredge-hard-floor-vacuum/ you can download a manual for you vacuum. Look on the right side of page for "downloadable documents and click on the manual.This will give you ... Bissell Vacuums

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???

Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!

Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!

Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

When I sart to run my bagless vacuum, it runs for a second and then shuts off. I replaced the belt and the filter. The repairman told me that on bagless vaccuums, the motor and bearings get clogged w

Take the brush roller off and on the ends are the bearing caps.try to take those off and clean the bearings ,carpet strands and hair will cause that.after you do that make sure the roller turns freely if not then the bearings might be bad and if that ... Vacuums

Electrolux 2 in 1 Ergorapido stick Vacuum. Motor runs then cuts out after 3 - 4 seconds. Sometimes it will run properly for 10 minutes so batteries are good. Why does it cut our usually?

If the hand held is working correctly (By itself) try pulling up a little bit on the 4 metal connection tabs on the wand. The connection tabs were not making a proper connection on my unit. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

Hello! I have a Kenmore Progressive bagless vacuum with the Easy Clean extended life filter. The model number on my vacuum is 34728401. I was vacuuming the carpet when it just stopped running. The dirt sensor light will come on, but nothing else. The belt looks fine, and I don't see anything keeping the beaters from rotating. Help Please!!!

You can have power to the dirt light sensor, but it seems like the motor itself is not using the power supplied. ... Vacuums

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.

\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.

Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

Engine troubles I have a 1975 4x4 GMC full size van. The motor is a 350 cid small block on propane. The thing hadn't been running in 5 years and when I tuned it up I changed vacuum advance pod on HEI distributor and hooked to a better vacuum and now the hotter it gets the faster it idols and when I try and turn the timing back, it starts hard. Wondering if vacuum is too strong or what is up?

I haven't fixed it yet but I think I might have a solution for it. From the factory this thing had a 4 barrel carb and they put an equivalent size atomizer in it for the propane and over the years someone omitted the EGR system in it and propane is a ... Vacuums

Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.

You need to replace the belt. Replacement Vacuum Belts ... Vacuums

My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look

... Kenmore Vacuums

Kenmore powermate vacuum 116.5818380 take hood off to get to bel

... Kenmore Vacuums

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks

... Sunbeam Vacuums

The pipe to the main cylinder keeps getting blocked. what is the easy way to clear it? i don't have a manual for dyson dc17 vacuum. where can i get an instruction manual?

Go to www.dyson.com and select your country in the dropdown menu, then call their Customer Service as they should have tips, pointers, and access to manuals. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.

I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

No rotation dirt not getting picked up - Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Replace the belt. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Really LOUD Just recently this vacuum went from the normal everyday vacuum to now sounding louder than my power saws in my workshop. Checked for clogs.. everything is clear.... cleaned it all over and then turned it back on and.... The neighbors thought I was running a saw mill out of my house. HELP!

Its the belt if it is a savvy.Have the same problem ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1522 seconds