Having problems with your Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum ?

Replacing Power Cord Kenmore Progressive Upright

\015 I read your comment on replacing the power cord on the Kenmore Vacuum and got the vacuum opened and right to where the cord should go but the wires are not connected. I have a black wire with a switch on one end and a white wire on my power cord. Inside I have a black cord and another black cord with white stripe coming up from below. Then I have a small circuit board with black and white smaller wires. Also a light with a black and white wire coming out of it. I am assuming I connect black with other black wires and the white wires with the black wire with the white stripe. Does that sound right to you. Thanks for any help. Steve\015

Answers :

That actually sounds correct, if it's the model I'm thinking of. As long as you're talking about connecting to the wires that are held in by the wire nuts you should be good to go.
\015\012
\015\012-R
Repair Help & Product Troubleshooting for Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacing Power Cord Kenmore Progressive Upright


That actually sounds correct, if it's the model I'm thinking of. As long as you're talking about connecting to the wires that are held in by the wire nuts you should be good to go. \015\012\015\012-R ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

How do you replace Kenmore progressive power cord?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

My kenmore progressive caniser needs a new power cord. the plug had one of the metal prongs break on the plug. how can I replace the cord? model 22812201


I do not know if you want to replace the replace the power\012cord or the receptacle for the power wand?\012\012If you need the prong for the power cord you can purchase a\012replacement power plug from a local hardware store and it will functi ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Replace power cord on kenmore model 11631912100 upright vacuum


... Kenmore Vacuums

Replace kenmore progressive vacuum power cord on model 11622612205


... Kenmore Vacuums

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david


Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

Kenmore Canister 116.20712007 replace power cord


... Kenmore 22612 Bagged Canister Vacuum

How to replace power cord on Hoover WindTunnel upright vacuum


The aforementioned solutions probably never even attempted this fix on this model. The handle does NOT need to come off. but the 5 screws on the front housing DO: 2 above the light and 3 below it. Then to get the colored housing off you need to acc ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

A family member recently gave me their Kenmore Vacuum Cleaner (model 35821) and I did not notice that the power cord was missing at first. I tried to look closely at the manual online to see if this was something I would be able to purchase or if the vacuum was no longer any good. Do you happen to know if there is a replacement part for the actual power cord for this item?


Any power cord 17 gauge or lower will work ... Vacuums

Replacing a fraayed and twisted power cord on a Hoover windtunnel upright


Ok so I took this vaccum apart completely except for the electrical and motor systems. It seems to me that without dismantling both of these systems on the vaccum you can't replace the power cord. And I wouldn't recommend taking them apart unless yo ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

HOW DO I REPLACE A POWER CORD? HAVE THE CORD, DON'T KNOW HOW TO TAKE THE CASING APART ON POWERFORCE UPRIGHT


Push a SMALL screwdriver under the rubber handgrip. Put a fre drops of alcohol into the opening where the screwdriver is. This will llubricate the grip so you can get it off. After you repplace the wire, use alcohol to put the grip back on. It wi ... Bissell Vacuums

Kenmore elegance bag replacement - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

How to replace kenmore 116 power cord - Kenmore whispertone 100 model 116


... Kenmore whispertone 100 model 116

Kenmore canister vacuum cord reel replace - Kenmore 25512/ 25513 Progressive Canister Vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I just bought a good Sears Kenmore Progressive 300 upright vacuum (116.38812891) today at a garage sale for five bucks. I left my relic Electrolux with the new owners of my former home during a recent relocation. In the interim I bought a Bissel 3750H which I do not care for, and borrowed a Eureka 7685 AU which performs somewhat better. I cleaned up the Kenmore, and though it seems to run well, noticed the drive belt is showing signs of degeneration. I would like to replace it, but was unable t


... Vacuums

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Replacing the electical cord on Kenmore Progressive Vacuum


To the right of where the cord comes out of the machine is a large screw. Remove it, and slide the upper handle assembly free. \015\012Then, on the front of the machine, remove the screws located toward the top of the vacuum just inside the bag ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have a Kenmore Upright Model # 11630412001 with a broken power cord


What about the cord ,that he cannot figure out.... ... Kenmore 35912 / 35913 Progressive Upright Vacuum

How to replace the power cord for the kenmore vacuum 11620512003


I figured out myself,,,,,,,,,the return spring was the BIGGEST challenge,,,whew.....overcame that obstacle with a pair of vice grip plyers......... ... Kenmore Vacuums

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum

Replace power cord on Dyson DC07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


The following link will take you to an article on how to change the motor on a DC07. Look at photos 4, 5 and 6 which shows how to disconnect the power cord.\015\012\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to replace electric cord on kenmore upright vacuum?


Take it to a good/ well known repairer for the changing ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1075 seconds