Having problems with your Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum ?

The carpet motor and light does not turn on when dial is set to "carpet"

Answers :

Check the plug on the power head. it may have come loose.
Repair Help & Product Troubleshooting for Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The carpet motor and light does not turn on when dial is set to "carpet"

Check the plug on the power head. it may have come loose. ... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

On my dyson dc 28 the carpet cleaning bar turns easily by hand, but does not turn on when the cleaner is reclined from the upright position. The white light illuminates when preseed, but the red light does not illuminate even though the motor is running. Thanks

... Dyson DC28 Animal Bagless Upright Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Carpet setting not working, no brush turn, no light, etc.

If the motor is running, its the belt, if not there is a break in your wire likely in the stub going from the wand to the head ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

My Kenmore canister vacuum (model 11627515700) will not turn on. Although when I set it to CARPET the agitator does come on, however the vacuum still doesn't. Is it likely a motor or switch problem??

Your motor in the canister part of your vacuum is bad you can by a nee one for about $84..They have them used on ebay for $40. just type in Kenmore 116. The reason why your agitator is working is because your agitator has a separate smaller motor. Yo ... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on

... Miele Blue Moon Bagged Canister Vacuum

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r

... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely

The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?

Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

When i set it on carpet instead of bare floor it is hard to push when i vacume (when i turn nob it only has two settings floor and carpet no high pile or low pile)

Hi there,Sorry to hear you're having difficulties using your DC14 on this particular carpet. You may want to contact your carpet manufacturer to check it's suitable for cleaning with a vacuum cleaner equipped with a revolving brush. Manuf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

The dial that you turn on hard floors or carpet,when in carpet slips by and then go past and makes a awful noise will not stay in carpet position to vacuum on carpets.

... Dyson DC33 Multi-Floor Upright Bagless Vacuum Cleaner

Belt wont turn makes a loud noise when put on carpet setting

If this is a Dyson with a protected belt that can't be replaced then it will have to be sent out to Dyson or get a Dyson servicepersonnel to check it over - protected belt motors are difficult to fix by yourself. If its clicking all the time, then it ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a

... Electrolux Vacuums

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like

I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

I was just using my Bosch 1450W bagged vacuum and all of a sudden, the motor just shut down. No warning, no problems. The light still turns on, but the motor is unresponsive. There is a clean bag and filter, and nothing caught in the front roller. The motor sounded fine - no shaking, or weird frequency variations. There were no weird smells, just a little bit of heat, but nothing beyond normal. I've had this thing for several years, and never had a bit of trouble with it. Any suggestions

Many vacuums have internal thermal switches that need to cool to allow the vac to operate. After 30 minutes, check all 3 air filters and try again.\012Gary ... Bosch BSG71310UC Bagged Canister Vacuum

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net

What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums

Won't turn on, red triangular warning light turns on. It worked a few days ago and now nothing happens when I press the button to turn the motor on. I have a Meile Champagne canister vaccum that won't run.

HiThe bad news is 99.9% the motor is gone ... Miele Blue Moon Bagged Canister Vacuum

On/Off switch. When the switch is set to "Floor" setting the vacuum will not turn on. When the switch is moved to "carpet" setting the vacuum starts.

Because floor means for lanolium it may have a sensor that detects carpet or linolium ... Kenmore 35821 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.6191 seconds