Having problems with your Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum ?

Burning smell. i think the belt is broken. how do I fix it?

Answers :

Turn the power head over and you will see (2) screws. Remove the screws and the top cover will come off and you can get to the belt. Here is the belt you need:

Kenmore 23812 Belt
Repair Help & Product Troubleshooting for Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Burning smell. i think the belt is broken. how do I fix it?

Turn the power head over and you will see (2) screws. Remove the screws and the top cover will come off and you can get to the belt. Here is the belt you need: ... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?

If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode

... Hoover Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning.  If the vacuum is left on any longer the belt starts smoking.  I took the case off and there was a little debris but not much.  Is there a cause and fix or just time to replace the belt?

Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum

Beater bar will not turn, think belt is broken, but do not know

The model number of the powerhead would be helpful - usually there is plastic cover with a lens for the light, push inward on both sides and the cover will pop offthere are two screws under that OR, there are two screws on the underside of the unit - ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I changed the belt on my bissell Cleanview revolution 3596 twice and both times the belt burned and starting to smoke. I'm not sure what to do now I have two broken belts what could I be doing wrong?

Sounds like the brush that the belt runs (or is supposed to run) is being kept from turning. If you can get the brush out to clean it and lubricate the ends that go into the holder clips, this should solve the problem.\015\012With the new belts burn ... Bissell CleanView 3596 Bagless Upright Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?

... Vacuums

Kenmore progressive model 38812790 smelled like rubber burning then the brushes stopped turning. Does it have a belt, if so, how do I get to broken belt to replace?

... Kenmore Vacuums

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie

Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?

... Vacuums

I am smelling a faint burning rubber smell and I think the belt needs changing, but I can't figure out how to open the case to change the belt. Can you help me?

... Hoover U5068-900 Sprint Upright Vacuum

Proheat 8910, just used once, pump belt keeps breaking. I replaced it two times, there is a burning smell and then when I look at the pump belt, its broken.

... Bissell 8910 ProHeat Clear View Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]

You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

Houver Cleaner My self propelled windtunell baged Vacumn has a broken belt. The small visible one that is visible is intact. This is the thick belt. I cannot for the life of me figure out what to open and how to replace it. The model # is U6 401-9RM I keep asking for a manual online but it doesn't recognize this number. I am 67 yrs old broke and fix it challenged..lol can you help me?

Take off the bottom plate, The flat belt ges around the motor shaft and then around the bigger pulley by the V belt. It will stretch to o on.\015\012\015\012 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Broken belt how to fix i have a belt - Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Take off belt cover on the left side of the top cover, turn cleaner over, take out screw from red lock and remove, pull cap and brush roll out, unhook the cogged belt, then you can replace the pump belt thru that opening. Put belt over the pump pull ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...

Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums

No action Hi: My brush roll won't budge. After we cleaned out all the hoses and replaced a badly worn belt (burned?) when I turn it on the smell of burning rubber and smoke has continued. What hurts is that I don't think I've used the vacuum a total of 10 times ... and I had such high hopes. Ideas?

I had the same problem with the belt breaking and the roller not spinning. I read about giving the roller a couple of revolutions to seat the belt, so I put another new belt on. It still didn't spin. I realized it was the end cap that was not spinnin ... Eureka 2961AVZ Bagless Upright Vacuum

I have a bissell 7.5poweramp uprite vacuum with a broken belt for the brush. What size belt would i need to fix this?

I have a galexey 3507a500 and my belt broke and i can't find a replacement belt at any store where do i get a replacement belt for a 5275 belt. ... Vacuums

I got a plastic bag caught in the DC17 Dyson Vacuum. It will not turn now. I do not think it is the belt, as it is there and not broken. The belt and/or the roller is not turning

You need to remove the plastic bag.thats stopping everything ... Vacuums

Brushes are not spinning. think the belt is off or broken. how do i access the belt?

There is no belt in this machine. The brushes are turning by an air driven turbine. The turbine has a pivot bushing made of steel inside of it that gets rusty because of the water that is running through it. The turbine will have to be replaced an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Bristles quit rotating and smelled like something was burning. It isn't the belt that turns the bristles. Can't afford a repairman, can you help me fix it?

Belt can reamin intact but still jam and burn. It won't necessarily break. I suggest you remove the bottom of the vacuum where the bristles spins and where the belt is located. You may have something jammed in there. You may need to remove the bristl ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a bissell healthy home vacuum and the roller bar on the base of it is not working. I have checked it for obstructions and it is clear. I have also tried reseating the canister and just about everything I can think of. It's almost like the switch that deterrmines whether or not the vacuum is in the upright position is broken and always says it is upright... any way to fix that? Thanks, Scott Hammersley

... Bissell Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0852 seconds