Having problems with your Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum ?
The hose is clogged in my Kenmore progressive 116.28614 vacuum.
The clog is near the end of the hose -- towards the bags but below the elbow in the hose. How can I unclog it?
Repair Help & Product Troubleshooting for Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The hose is clogged in my Kenmore progressive 116.28614 vacuum. The clog is near the end of the hose -- towards the bags but below the elbow in the hose. How can I unclog it?
... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum
When I switch it on the plastic compartment which holds the bag starts to be sucked in towards the bag and there is no suction at the end of the hose
Your Hoover U5076 has a clog. Fist unplug the vacuum from the wall socket. Remove the attachement hose from the door on the head, close the door. Remove the screw just below the main bag compartment, with a phillips or flat head screw driver. Be sure ... Hoover Turbopower Dual U5076 Vacuum
I have an old Miele canister vacuum and I do not know how to disassemble the hose to check for a clog. I think it sucked up a nerf ball the size of a ping pong ball. I changed the bag but it did isn't appear to be in the bag. The vacuum powers on but I do not have suction with the hose, and since the hose has hard plastic elbow joints I do not want to pry them apart and break it
Hi Emily: If you have the model number for your machine you may be able to find your manual on the Miele website. Check ... Miele Vacuums
Kenmore progressive vacuum model: 116.25614506, I replaced the bag and filter and now it seems to **** the bag up against the hose outlet with very little suction at the hose end
... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum
Kenmoore Intellivac w direct drive suddenly started making internal sound like something was stuck. Hose is clear, and sound is made when hose is detached from main unit. Vacuum sounds find at lower pressure, only makes sound with bag door closed and/or placing my hand over the end of hose.
Shut off the vac and open container and remove the bag. Try dropping a coin into the hose, then raise up to see if it falls thru to the bag area. If it does check the throat of the vac where the dirt is sucked upward to dump into the bag itself. ... Kenmore 35912 / 35913 Progressive Upright Vacuum
Inside the my wd09450 there is a part missing which holds the dust bag on to the end of hte hose. the rubberized port of the bag should fint over it. where can I get one?
Our plug got pulled out (by driving away while the canister was still plugged-in after a vacuuming the car). How can we open up the unit to reattach the wires? We accessed two sets of screws (2pairs) toward the bag-end (not the motor-end) of the canister, but we can't locate any access for the two other apparent screws inside the body.
Remove all visible screws. Top and bottom, then once they are all removed, take a flat-head screwdriver and slowly pry around the canister until it comes completely loose and can be removed. Then you should have access to the wires which can then be ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
I'm trying to change the filter....One person told me to open the hose end and take the bag out and go from there, but that isn't the right way!!! It's the other end where a couple brushes are able to be stored on top of the canister, but I can't figure out how to get that section off..it's as tight as a drum HELP PLEASE and thanks. Betty
There's a tab at the middle of the lower back of the tool holder (air diffuser). Pressing in on that tab should enable you to lift the back of the holder first, then lift off the whole thing. It will come off, just make sure the tab is in far enoug ... Electrolux Epic 6500 Vacuum
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums
My new Kenmoore Powermate 116 canister has poor suction. I have no pets and light dust. Its not picking up small particles on the wood floor with the floor attachment. When I put my hand to the suction it feels weak. Cleared hose and changed bag. Using again, same issues. This should not be happening with a new vacuum. Is it a bad design in the elbow joint of the hose? I want to return this!!!!
First of all disassemble the handle and hose as much as possible and examine the inside. Make sure there is not any significant debris lodged in the hose somewhere like a plastic bag or something.\015\012\015\012Also check at the top of t ... Kenmore 23912 Progressive PowerMate Bagged Canister Vacuum
Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?
Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums
How to open 116.23512301 vacuum canister AC section to wire in replacement 4370608 cable assy. This assembly contains the receptacle that powers the hose. I found the two screws below the bag cover, but can't figure out how to release the end near the retractor lever.
... Kenmore Vacuums
Bag is not full but little vacuum at hose end. Why?
You can have one of several problems:\015\012\015\012(1) A clogged hose, or\015\012(2) A clogged filter or bag. \015\012\015\012If the filter or bag is clogged, it restricts the airflow to the hose end. ... Vacuums
Hoover windtunnel dirt finder light stays red. We've cleaned the elbow the roller the hose and have a clean bag. The vacuum is new only had it for 3 months.
I'm not sure about a 3 month old vac, I'd probably go the warranty route. However, for the older vacs thy start getting false positives. The sensor is simply a microphone hooked to a computer chip detecting sounds of dirt entering the bag. \ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I have an electrolux epic 6500 sr. The change bag light came on, I changed the bag, now it won't run properly. If the bag is out and the hose attached it will run or if the bag is in and the hose is off it will run, but not if the bag is in and the hose is attached. Any suggestions?
First, if it runs without a bag, there's a problem with the bag lock-out switch or wiring. This needs to be replaced/repaired by an authorized Aerus Electrolux technician.\015\012\015\012First, turn dial on top of vacuum counter-clockwis ... Electrolux Epic 6500 Vacuum
How do I get a plastic bag unstuck from my vacuum hose?
... Bissell Vacuums
I have a dyson DC07. The hose has come away from the hose end and the end is stuck in the top end of the wand as it sits in the upright position on the machine. Any ideas as how to get it out? If I can get it out it might just be a new hose. If not, it's a new hose and wand.t
... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
Where does other end of hose go
You're quite right . . . the manual doesn't show where the other end of the hose goes, which frustrated me as well. I finally found another pic of the cleaner (I think it may have been the one on the box) which revealed the answer. If you're facing ... Hoover F5906-900 Upright Steam Vacuum
I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!
Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums
The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is
... Samsung Quiet Storm 9048R Bagged Canister Vacuum
When I flip the switch on my sebo x1 upright, a red light comes to the brush and bag icons. However, I cleaned out the hose and checked to make sure there is no obstruction from the brush to the hose also, or from the hose to the bag. It is clear that juice is coming to the vacuum, but there is no sign of life except the two red lights.
Thanks for contacting fixya. You should pull out the bag and reset the machine. You should take all the user replaceable items. And turn it on. You will get lot of errors. Then turn the machine off. Put back all the accessor ... Sebo Automatic X1 Bagged Upright Vacuum
DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each
Should be a pry off dot on the underside revealing a screw ... Vacuums
I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss
Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum
I have a new bag in, checked the hoses for clogs have the motor cover off showing motor runs. Problem is vacuum has no suction in hose area, cover off where bag is and the air blows out of filter. hoses are clean no blockage.
Have you checked the filter? Many vacuums have a filter under or behind the bag to keep dust and dirt out of the motor. If this gets clogged the motor can't get any suction. Also look for holes in the hose or in the small segment between hose and bag ... Vacuums
I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!
... Miele Vacuums