Having problems with your Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum ?

Sock stuck in hose midway. Unable to getit out with wire or brrom handle. Is there a way to take hose apart at either end.


Answers :

If the sock is midway, taking either or both ends apart won't help. Take it to a vacuum repair shop and ask them to try to unplug it. You may need to buy a new hose.
Repair Help & Product Troubleshooting for Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sock stuck in hose midway. Unable to getit out with wire or brrom handle. Is there a way to take hose apart at either end.


If the sock is midway, taking either or both ends apart won't help. Take it to a vacuum repair shop and ask them to try to unplug it. You may need to buy a new hose. ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

E series power head handle, internal wire came lose


Here is a pix.\015\012\015\012 ... Rainbow E series Canister Wet/Dry Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

Power head handle wiring


That wire goes just above where the trigger is, take the trigger out and there is a slot that the end goes into. ... Rainbow E series Canister Wet/Dry Vacuum

I have a Dyson DC22 that seems to have lost a lot of suction. I can't peer right inside the wand, but it seems that hose may have disconnected from the telescoping handle allowing a huge leak. How can I take the handle apart to inspect/fix this?


... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

Something stuck in my hose to my Capricorn model. Is there a way of taking the rotatating handle off the hose?


... Miele Vacuums

All of a sudden the hose isn't sucking. There is nothing in there that I can see. Is there a way to take apart the connection between the hose and machine?


This URL would be a good place to start looking:\015\012http://media.dyson.com/downloads/us/floorcare/manuals/dc17_opmanual_usa.pdf\015\012\015\012\015\012\015\012Pay special attention to the belt that drives the beater brush and the beat ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?


The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

My Kenmore progressive canistor vacuum has a loose electrical conection in the hose handle. How do you take the handle apart?


There are 3 visible screws there in the handle and one not so visible. start by removing the 3 visible screws.Take a flat screwdriver and pry off the colored portion of the handle that would contain the switch. There is one mo ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My infinity vac NV29 seems to have an extension wand stuck down in then tube and I am not able to get it out. We rented our winter home and evidently they found some type of extension that did not belong to it. Is there a way to take the handle apart in order to remove it? I am not able to use it with the handle and have to use the one on top of the canister, which is extremly difficult for me since I am disabled. Thank you.


... Euro-Pro Vacuums

I'm trying to change the filter....One person told me to open the hose end and take the bag out and go from there, but that isn't the right way!!! It's the other end where a couple brushes are able to be stored on top of the canister, but I can't figure out how to get that section off..it's as tight as a drum HELP PLEASE and thanks. Betty


There's a tab at the middle of the lower back of the tool holder (air diffuser). Pressing in on that tab should enable you to lift the back of the holder first, then lift off the whole thing. It will come off, just make sure the tab is in far enoug ... Electrolux Epic 6500 Vacuum

Hi, I vacuumed a small rubber bouncy ball up into the vacuum by mistake. The suction is not as strong now, and I'm not sure what to do. Where I can easily take the hose apart (eg. at the handle places) I cannot find the ball. What do you suggeest?


... Vacuums

I sucked up something I shouldn't have is there a way to take apart the hose and get it dislodged? thanks


Try running a straightened wire hanger through the hose.\012try from both ends ... Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it


It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

I need to take apart the electrolux epic 8000 hose power end


... Electrolux Vacuums

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!


Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

Hose is there a repair manual for the hose on this kind of vacuum?? it got clogged pretty good and I thought by taking the hose apart there was a place to take the hose out.... I thought wrong and now I have a hundred piece everywhere and no vacuum..


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Clogged hose... I have a clog in my hose, probably a sock, I have pushed it through to the hard plastic handle end of the hose, help! can the plastic handle wand be disconnected from the hose to remove the clog??? Thank you


Hi!\015\012 \015\012Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Con ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have some sort of object in the hose of my Epic 6500. I have tried reversing the hose and blowing out the foreighn piece of debeis but this has not worked. Is there a way to remove the plastic connector end to access this end of the hose? Or is there another solution to this problem?


By reversing it, I assume you plugged the hose into the exhaust blower on the top of the machine. If so, insert the other end into the intake and turn one the vacuum. This way the clog is also getting sucked at what should be the loose end.\0 ... Electrolux Epic 6500 Vacuum

How to reattach the hoses on the bissell 9200 model after taking it apart


... Bissell Vacuums

There is a cut at the end of the hose. Is there a way to cut the hose at the split and reattach it to the connection? Thanks.


Unfortunatly the amswer is no you will have to replace the whole part. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0597 seconds