Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

Brush does not turn on my vaccum

\015 The vaccum is a sears Kenmore canister type, and it has a motor that turns the brush and a light for nigth vision. neither the motor or the light work.\015\012\015\012My problem is similar except that light works intermittenly and I hear the motor running both from the canister and from the powerhead. I was told by a local vacuum repair shop that I needed to replace the hose for the reasons you specified - that the connection wasn't being made between the handle and the powerhead (something that appears to be quite common in Kenmore canister vacuums) but my problem appeared to be at the handle end with the plastic "holes" breaking apart so they didn't hold the prongs. So I ordered a new hose online and when it arrived, I found that the vacuum would run on the setting for carpet (meaning the light would turn on and I would hear the motor) but nothing happened when I tried to run the vacuum on the floor setting. I called the company that supplied the replacement hose and they think it is the vacuum's motor (not on the powerhead but in the canister). What is the likelihood that this is my problem?\015

Answers :

If there is no suction when you disconnect the beater bar assembly near the hand hold where you grab the vacuum, then there may be either a restriction in the vacuum line between there and the vacuum section (that rolls around behind you), or the vacuum line from the handle point to the rollaround section is not properly connected. This all assumes the vacuum motor in the rollaround is running.

The beater bar section does nothing but cause dirt particles to be sucked into the vacuum system. The vacuum or suction is created in the rollaround unit.
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.


Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor sid ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The spinning brushes on the vaccum no longer spin, how can i fix this? The vaccum picked up a very small wire from a video game and i turned it off immediately. I unwound the wire but the brushes no longer spin.


You have either broken the belt or more likely the clutch easiest is to replace cleaner head assembly \302\24375ish or call Dyson and arrange a service if you're not DIY inclined but check belt !st ... Dyson Ball DC24 Bagless Upright Vacuum

Vaccum brush not working. Filters clear of debris has been smoking will not **** anything up help! I cleaned the brush up, cut hair out, etc. Still the brush will not turn and it smokes a little, is this a belt problem?


Yes you need to change the belt. Here is a link to the belt you need and to a manual you can view:Bissell Lift-Off Revoluti ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Brush does not turn on my vaccum


If there is no suction when you disconnect the beater bar assembly near the hand hold where you grab the vacuum, then there may be either a restriction in the vacuum line between there and the vacuum section (that rolls around behind you), or the vac ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dyson DC07 Vaccum - brush will not turn


Hi.\015\012\015\012Your Dyson has A clutch unit this engages the brush roller when you pull the handle back to vacuum.Check the clutch control knob which is at the bottom left side of machine looking from the front. It s ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush does not turn on my vaccum


When you attach the hose to the wands, there is a connection made between the hose electrical receptacle and the cord from the powerhead. On the Kenmore, it is common for the receptacle on the hose to break away from it's seat and slide back into the ... Vacuums

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum

VACCUUM GOES ON, MOTOR WORKS, BRUSH WONT TURN WHEN THE VACCUM IS TURNED ON.


Check the belt, and remove any objects clogged in the roller system ... Dyson Vacuums

Roller brush will not move when vaccum is turned on


Maybe the belt is broken. clean the unit and replace the belt. ... Kirby Ultimate G Bagged Upright Vacuum

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I would like to vaccum my new ceramic tile and wood floors with my ulta lux 2000 how do you get the beater brush to stop turning so that it will not scratch the floors?


There should be an on/off switch on the right top of the power nozzle. If it's been running, then flip the switch. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Kenmoore beltless vaccum brush wont turn - Kenmore 35912 / 35913 Progressive Upright Vacuum


... Kenmore 35912 / 35913 Progressive Upright Vacuum

The vaccum turns on but the brushes dont spin, and i have hit the reset button on it already...


Vacuum turns on and sucks but the brush does not spin and I have pushed the reset button ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Can I use my ultra lix 2000 to vaccum my new ceramic tile and wood floors? It so how do you stop the beater brushes from turning so that they do not scratch the floor?


Yes you can, just set the height at maximum. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Vaccum sucks really well seems like brushes not turning?


Could be!-- Can you look at the brushes, while the vacuum is running, and be sure? If the brush is NOT turning:Is there a switch that turns it on/off? Does it work correctly?- or is it suspect?If it is turning the li ... Bissell Vacuums

The belt broke on the helix bissel vaccum and when I put the new one on the brush does not turn - is that right?


Provided it's the proper belt, perhaps a twist of the belt is needed, as some go straight, others have a 180 degree twist.(like a figure 8) If that doesn't do it, get back with make & model of machine please. ... Bissell Vacuums

I have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Company Wind Tunnel U53019 Upright Vacuum

No vaccuming The brush is still turning so the electricity is still going through but it's not vacuuming. Push the button and nothing is happening. After only 10 minutes of "working". thanks!


Leave it to Cool may have tripped themal switch ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

My Dyson Aminal Vacuum simply will not turn on. I plugged it in this morning, pressed the power button- and nothing. No warning sounds, simply silence. Sigh. Nothing is wrong with the wall outlet.The vaccum is 3 years old but has run perfectly until this point. The brushes are clean of any accumulated hair. What part might need replacing?


The power switch may need to be replaced. Call the Dyson helpline - they will give you the location of an authorized Dyson dealer in your area who will be able to replace the switch. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Roller brush bar wont turn after te machine made a popping noise then just only the vaccum is now working


I had this exact problem after moving the machine by car. after opening the machine there is some dampness so suspect popping was caused by liquid mixing with electricity. The machine does have drain holes so leave it upright for a week or two and t ... Bissell 9200 Upright Vacuum

I have an oreck xl and the vaccum wont hardly push. Is it the belt? The brushes aren't turning when I lay it on it side. How do you replace the belt? If you can give detailed instructions I would so appreicate it . Thanks


On the side of the head you'll see a removable plate with one screw. Remove the screw and slide the plate towards the front until it's off. You'll see the belt. ... Oreck XL21 Bagged Upright Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1372 seconds