Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together


Answers :

Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together


Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off ... Kenmore 25512/ 25513 Progressive Canister Vacuum

How to refit the front brush belt driven roller ? We removed the roller accidentaly when cleaning out hair that had got wrapped around the roller. How can we put it back in?


Hi well if you go onto youtube and look for replace dyson clutch it will show you how to refit your brush good luck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?


The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

Ive got a dc07 dyson just changed the belt on it as i had to since then it isnt picking anything up at all nothings clogged up had it to bits and put it all back together again properly. The hose is working when i take it off its got plenty suction but when i run it along the floor it picks absolutely nothing up any ideas that i havent thought off. Thanks


Sounds like the hose underneath has become detached. Have a look and if its not that come back to me. Also can yo9u check your U Bend is still on as these can come off. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

We took it apart to replace the belt and put it back together and now the roller is not engaging my carpet like it use to. the roller is spinning. model # 8955


... Riccar 8955 Upright Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Putting the roller brush back together


... Riccar 8850 Vacuum

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper


... Vacuums

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I am trying to install new belt. I got the bottom of the vacuum off, but now I need a diagram on how to put it back together.


... Eureka 431A Optima Bagless Upright Vacuum

Turbin hey its me Lisa I took the turbin apart and know where the wheels (gears) go but they have this little bearing or what ever it is its round and has a whole thru sent can't figure out how it goes to put it back together. the thing turns really good now after I soaked it HELP


You should have it all back together now. Hope it is running ok. \015\012Lauren(reddevil6) ... Hoover F7220900 SteamVac V2 Upright Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums

I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?


The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums

I took the vacuum apart, and cleaned the filter, cannister reservoir, removed all the hair which was wrapped around the beater bar. One the filter was dry (next day), I put it all back together. Now, there is no suction, and it sounds differently than it did before.


Check its assembled correctly . Sounds like something is out.... ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Hoover model U6476910 I was cleaning out the bearing sections of the brush when a spring type pressure washer fell on the floor. I did not see the washer when I took it apart and I can't tell where it goes in order to put it back together. It is very thin and measures about 5/8 inch with an 11/32 inch hole. Frank Nething


Hi frank this sounds like its a compression washer, you normally find these on the end of the roller to even out any movement from side to side, as you look at the hoover's brush head, it should slip into a groove on one side with the roller...hope t ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Need the manual on how to run (put together and all) the hoover steam vac v2 (widepath) with auto rinse) we tried today and when we leaned it back (so we could run it on the carpet) water started pouring out all over the machine and got the carpet (like flooded) wet :( this one was me mom's and she passed on approx 2 1/2 years :( she always kept the manuals for everything but we caint find this one :( ... thnx


God Bless Your Mom.\015\012\015\012Hope this was helpfull to you. Sawdust46\015\012\015\012http://www.hoover.com/pdfs/manuals/F7411900.p ... Vacuums

I just purchased a Dirt Devil machine on Monday, I finally got it put together today and the brushes are not moving, dust is swirling around but no brush movement, I have changed all the nap settings, nothing, I am having company tomorrow and I threw my other vacuum cleaner away, HELP ME. Thank you.


Sounds like you may not have the belt attached or it is broke. ... Dirt Devil Vacuums

Loud noise?? my vacuum suddenly just got really loud. it suctions fine, i changed the belt, but when the roller is off its not loud, but when i put it back on the 11noise is horrific. it vacuums fine i just cannot stand the noise. please help


I have the exact same problem. I've taken the thing apart and cannot figure out what is causing the noise. It's not the belt and it doesn't seem to be coming from the engine. It sounds like the spinning brush is hitting something, but it's not, th ... Bissell 6590 CleanView Bagless Upright Vacuum

HI, I HAVE ELECTROLUX LE(similar to 2000). I HAVE TAKEN IT APART, CLEANED IT, AND PUT BACK TOGETHER. IT SEEMS I GOT THE WIRING WRONG. CAN ANYONE GIVE ME A SIMPLE WIRING DIAGRAM FOR THIS VAC? THIS MODEL HAS NO CONTROL KNOB. IT'S NOT COMPICATED BUT I MUST HAVE CROSSED SOMETHING BECAUSE IT SHORTS OUT NOW. HAVE CHECKED ALMOST EVERYTHING ELSE. THANKS.


... Electrolux UltraLux 2000 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0738 seconds