Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?
Schematic looking for a schematic ,vacuum isn't sucking and is going really slow
Sounds like the motor has gone bad. But you need to go to sears.com, click on the part link, put in your complete model number, usually starts with 116.************. Then a parts list will come up and if what you need is there, you can order it thru Sears. Sometimes underneath the rear top cover, is a schematic
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Schematic looking for a schematic ,vacuum isn't sucking and is going really slow
Sounds like the motor has gone bad. But you need to go to sears.com, click on the part link, put in your complete model number, usually starts with 116.************. Then a parts list will come up and if what you need is there, you can order it thr ... Kenmore 25512/ 25513 Progressive Canister Vacuum
My eureka Hello im not sure what kinda of eureka it is a friend gave it to us...and I went to change the bag and vacuum and the spinner isnt going...and i dont think its the belt...help please! i looked on the back and it gave me a modle number its 4475
The belt may look ok, but am sure it is stretched and when this happens, the brush roll won't turn like it should. Did you check the brush roll ends to see if they turn freely, if not replace it. ... Vacuums
Havent used for about two years. I had to put the belt on it. It doesnt seem to be sucking up very well and after about 15 minutes of vaccuuming the bag was empty. My house got really dusty. I know the rollers were spinning because i looked. I could hear some dirt going in but could definatly tell it wasnt working properly. Is it in reverse or something?
After two years you need to make sure the bag is connected properly and inspect it for tears and that the hoses are connected correctly and not deteriorated. Make sure the hose is clear. You should be able to feel the suction at the end of the hose. ... Vacuums
My Bissell 3760-1 has stopped sucking in the roller portion. The grab n go part are working fine. Checked the belt and it looks fine. Did I burn up the motor or a microchip?
Hey Lisa! Sorry you're having difficulty with your Lift-Off vacuum. Here's a link to troubleshooting steps to assist you with the suction.\015\012http: ... Vacuums
I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o
I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum
My vacuum isnt sucking - Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Even though the brush is spinning, you probably need to replace the belt\015\012because ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Hi good day, I have a Kenmore Grab n Go 12.0AMPS Vacuum cleaner, Model# 116.34722402 & serial#T53601507. The vacuum is now having a problem whereby the rolling brush underneath is not spinning when the vac is on. This has caused it to stop sucking up dust. Could you please advise as to what might be the problem. Thanks in advance for your kind assistance. regards, Clarance
... Kenmore 34722 Grab-N-Go Upright Vacuum
Electrolux Epic 6500 SR Carpet Sweeper won't go on. Belt good brush moves, bulb looks good, reset red button I'm not sure, works, looks good. Vacuum starts has suction ,
This link is the manualhttp://www.totalvac.com/manuals/electrolux_manual_Epic6500.pdf ... Vacuums
Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to
... Hoover U5344-900 WidePath Vacuum
My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara
My vacuum has suction with the long tube assembly but not any significant suction down by the rollers. I assume there is a clog or a problem between where the hose attaches to the machine and the rollers but I can't figure out where to look for it. HELP. I've only had this vacuum for a few months and I'm really dissapointed!
Go to the bottom of the machine and to the rhs of the rollers you can see the pipe - also remove hex panel on back and remove hose from elbow , i also found that a filter cx did wonders ... Miele S7210 Bagged Upright Vacuum
Soinds weird my dyson sounds like sucksion is leaking...the air leaking sound is really loud. it sucks some dirt but is not going into the canister, don't know where its going. it sounds like when i'm using the attachments when i'm just vaccuming...please help!!!
Dysons web site has an online area where you can walk through common problems like this:\015\012\015\012http://www.dyson.com.au/support/ ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
I have bissell powerforce turbo bagless upright vacuum. Its a great machine. It is clogged though. I think I was not emptying the dirt collection tray thing enough. How can I unclog it. Its not sucking up like it should. It sucks up most stuff, but its not going into the bagless tray thing like it should
Remove the hose , clear that , then if you take a wire hanger apart you can pull whatever is remaining out of that connection, also remember to clean ( if you have the cleanable filter) the filter and also the top one ... Bissell Vacuums
I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?
... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum
LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.
Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
My Hoover Wind tunnel has even a cheaper on/off switch and now, you can't buy a new one. I used to go to their website which had a wonderful diagram of the 'guts' but now the only parts are the obvious ones, belts, filters etc....I have to vacuum twice a day and I should be the test person cause its on and off on and off, but now for a vacuum I purchased 3 years ago for over 200 bucks and I can't fix it myself really makes me made or do you know where I can get this part? help? if not, I will ne
Have you tried going to appliancezone.com? I go there when I need parts... ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
I just got a Kirby vacuum and it will stutter or shake when I vacuum in drive mode. Usually when I slow down near a wall and before I start going backwards. What does it mean?
Shampoo attachments... I have all these attachments for my vacuum but never needed to use them. It was my mom's vacuum and she can't find the manual so I'm in a rut and my rug looks like a herd of elephants have been all over it (the rug is also my mom's) so it really needs washed. Can someone please walk me through the necessary steps to get this thing turned into a super duper carpet cleaner? Thanks.
We have manual with plenty of pictures HERE.Good Luck ... Kirby G5 Bagged Upright Vacuum
I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f
I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums
My kenmore hida filter vacuum cleaner no longer has the sucking ability it used to have. It is only 4 years old and has worked extremely well up until this week. The motor is functioning well, as is the carpet brush function.... it just has a very weak suction... Is there any easy way to tell if it is blocked? An ideas of what is going on? thanks
Well i've hade one come in a while ago and it didn't have good suction so I looked at the bag it was buljing w/ dirt so I put a new bag in it and it had better sucktion but still not good enough so I cheched the fabrick filter and it was dirty too so ... Kenmore Whispertone 23312 Bagged Canister Vacuum
We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't
If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums
Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?
Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum
Looking for schematic for F5914-950 - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
You will not find a schematic for any Hoover products. You can only get via an authoriesed dealer. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hi my vacuum isnt sucking up like it should, actually hardly at all, the brush on the bottom is spinning, not sure what is the matter with it
Check all the hoses and filters for any blockages. ... Vacuums
Don't want an expert. I wan someone with authority that can make an intelligent decision regarding the way you sell replacement filters. It looks as though the patients are running the ward at HQ. This freak insane! Maniacal and just plain stupid! Tell me something Mr Expert, my closest choice was "vacuum expert" How is this expert going to know and fix the asinine way b&d devised a plan so that the consumer would enjoy wasting a better part of their day. Who, please tell me, who with a drop of
Ouch! So go into Lowes get a 10 pack of electrostatic register vent filters back in the furnace filter section. Take your old filter off and if it's a paper corrugated looking cone just wash it really good and dry it out...if it's disintegrating then ... Vacuums