Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?
Canister motor not on - power to power mate is on
\015 The power mate carpet cleaner on my Kenmore canister vacuum has power, but the motor in the canister section does not. Did not smell hot. The filter on the back side where the cord is, is dirty. The motor doesn't look excessively dirty and doesn't look as if it has ever been hot. Can it be a fuse in the vacuum? What looks like a fuse is sealed.\015
If its a long plastic tube with snaps on it that is where the fuse is.open it up and you will find the fuse
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Canister motor not on - power to power mate is on
If its a long plastic tube with snaps on it that is where the fuse is.open it up and you will find the fuse ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I have an old canister CP-D4 power-mate. The motor sounds loud and the switch glows when running. Does this sound like it is worth repairing.
... Kenmore Vacuums
I have a Sears Kenmore canister sweeper with the power mate, but it no longer has sufficient suction to pick up dirt. I took the machine apart and cleaned it, but it is still not sucking, does this model need to have the motor oiled?
When cleaning the machine, did you do a good job of cleaning the beater brush and making sure it turned freely in the holders on each end? Perhaps a bit of WD40?\015\012Also, a new set of belts might help a bit. ... Kenmore 22812 Bagged Canister Vacuum
We have a Kenmore canister vacuum cleaner 25614504. It has in intermittant light and power flicker in the power mate unit as it is moving over the floor. This behavior can be simulated by jiggling the power cord where it eners the power mate. I do not know how to enter the power mate to see if there is a loose wire.
... Kenmore 28614 Canister Vacuum
Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?
Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum
Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!
Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum
My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa
... Electrolux Vacuums
Hi, I have a Kenmore Whispertone canister vacuum that I purchased in 2007. The model # is 116.22271503C, which seems to confuse the parts people. I need to buy a new powerhead & a few months ago was given a price of $75, but now Sears Canada tells me the part # is 20 116KC5OXBZRZUO1 described as Power Mate Assembly for $192.99. I thought the Power Mate was the small powerhead for stairs, upholstery, etc. Have they located the wrong part for me, or is this really what it costs?? Thanks in advance
Yes, powerheads are quite expensive. That sounds about right.\015\012You can check Ebay for better prices, but check the shipping rates before ordering. ... Kenmore Whispertone 23312 Bagged Canister Vacuum
Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?
Kenmore power-mate 3.9 magic cord canister
... Kenmore Vacuums
I Have a kenmore 116.23612300 canister vacuum which will not start. I have power everywhere but nothing going to the black wire to the motor. Seems to stop at the pcb asm, #KC86WBZRZ000 . Nothing from there to the black motor wire. White wire to motor has continuity everywhere it should. Ruled out just about everything but the PC board. What does it do exactly?
... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
My kenmore model no 116.22512200 canister vacuum power head has no suction & doesn't pick up even though it shows all the signs that it is getting power. The junior power mate works fine.
... Kenmore Vacuums
Power-mate motor has a high pitched squeal, model 116.22950c
... Kenmore 25512/ 25513 Progressive Canister Vacuum
How to fix my kenmore power-mate 12.0 amps motor
... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum
Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v
Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums
I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger
There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums
Power Head keeps cutting in and out while vacuuming???Canister motor keeps running but the power head starts and stops like there is a short or some loss of connection somewhere. Any ideas?
My kenmore progressive vacuum had the same problem. The electrical terminal at the bottom of the wand was corroded. I used a flat head screw driver to scrape the female portion of the connector as best as I could. I then took off the plastic cover on ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
Kenmore canister power-mate
I was able to get the whole thing reassembled. If there is something specific that you are having trouble with let me know. Everything snaps into its specific spot--it is just tricky to get it all lined up.\015\012\015\012\015 ... Kenmore 25512/ 25513 Progressive Canister Vacuum
Have a kenmore canister vacuum cleaner which the power-mate parts don't work. I had loaned the vac out it came back with part of the hose smashed. I don't know if that is the problem.
The hose conducts power to the "power Mate" There are wires running end to end through the hose and handle. If your hose is grey with hard plastic cuffs at both ends, it is repairable, but you will need to locate the Smashed parts. If yo ... Vacuums
Won't start orange canister type,has change ba light hepa &motor filter,and power hose and beaterhead,put new filters in checkedthe hose,made sure it wasnt clogged
Take an AC VOLT Meter and place the leads of the meter where the power cord terminates,one on the white lead and one on the black. There should be 110-120 volts AC. If that is good then move one of your meter leads to the other side of the on switch ... Electrolux Epic 6500 Vacuum
Kenmore power-mate 3.9 magic cord canister - Kenmore Vacuums
... Kenmore Vacuums
Power buttons on my electrolux oxygen 3 canister vacuum won't activiate motor doesn't come on model EL7024A
... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
We have a Kenmore canister vacuum cleaner. the carpet cleaning attachment, I think is called the power mate has a beater that is intermittently working now
Contrary to your advice, the nozzel cannot be connected directly to the powerhead--the female openings are set closer together in the nozzel than the male plugs in the powerhead. ... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum
Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to
When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums
Kenmore 3.9 with power-mate Model 116 2839581. Can't locate screws to allow cover removal for access to motor
You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 22313 Bagged Canister Vacuum