Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

Vacuum won't come on

\015 My Kenmore 25513 won't come on. The carpet attachment/beater bar works, but the vacuum will not come on.\015

Answers :

The switch in the hose maybe bad, motor problem, or some of these cannisters have a relay mounted by the motor, it may be bad.
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The vacuum comes on but the standup vacuum assessory won't turn on. I"ve pushed the reset button; unhooked everything, including reattaching the canister but it still wont' come on. Any other ideas? By the way, I hated the price, but it's the best vacuum I've ever had - especially when I have three shedding pets!


Check the roller brush to see if anything is wrapped around it. If not, there may be a loose connection or wire between the canister and the power nozzle. I assume that's the accessory you're referring to. I could also be a defective switch, but loo ... Vacuums

Question mark light has come on my vacuum and it wont run. I replaced the bag, but it wont start. I don't have a new filter is that the problem?


... Electrolux Vacuums

Water wont come out - Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum


I have a Proheat 2X and had the same problem. I tried the Water Rinse setting and found water came out and was suctioned properly, but on the Light Clean, Normal Clean, and Heavy Traffic settings, the unit failed to do anything. Problem may be with l ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Water or cleaning solution wont come out - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Water wont come out fo the steam cleaner. - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Try adding a table spoon of salt to the water. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I own a elecrolux 2100. the power light comes on but the vacuum wont start


First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it's possible that the tubes connecting to t ... Electrolux Vacuums

Water wont come out the nozzles - Hoover F5411 SteamVac Jr. Canister Vacuum


Its plugged up somewhere along the hose or not connected correctly ... Hoover F5411 SteamVac Jr. Canister Vacuum

My dc 25 hose is jammed and wont come out? - Dyson DC25 All Floors Bagless Upright Vacuum


... Dyson DC25 All Floors Bagless Upright Vacuum

I disconnected the Kirby vacuum to blow out and clean under my refrigrator, when I put it back it wont come on, don't seem to be getting any electric.


Make sure your electric plug is still in place ... Vacuums

Water wont come out - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum


Hey Earnest! Sorry you're experiencing difficulty with your machine. We have terrific FAQ's to help you with the spray.Here's a quick link to the FAQ page: \015\012http://w ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Flashing light coming from where handle connects to vacuum


That's an item a tech would have to look at. If the machine is sparking bad, find your local service center. ... Kirby Ultimate G Bagged Upright Vacuum

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc


Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Over heating Light Comes on as soon as I try to turn the unit on. I have a Miele S558 Silver Moon vacuum that has only been used once and it shut off and will not come back on. The overheating light comes on as soon as I try to switch speeds on the handle or turn the unit on at the canister, and the vacuum will not run. Do you have any idea what the problem is?


... Miele s558 Silver Moon Vacuum

Wont come on or stay on


Take a look at my troubleshooting guide....\015\012\015\012http://reviews.ebay.com/COMMON-P ... Kirby Ultimate G Bagged Upright Vacuum

The vacuum tube keeps coming out of the back of the vacuum and dirt goes all over. How do you stop it from coming out?


The simple and obvious answer to me is Duct Tape.\015\012\015\012There should be a detent or similar latch arrangement on the part you are talking abut. It may be broken or you may not be getting it properly engaged. \015\012 ... Eureka 4700A Maxima Bagless Upright Vacuum

I have an older Fantom Fury Vacuum. When I turn on the power button my vacuum does not come on. The outlet works well with other appliances. I have used it already today and when moving to another room it would not come on. What is wrong?


... Vacuums

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

My bissell proheat 2x wont vacuum up water


There is a float (usually looks like a red ball) that rises up if water is in danger of getting to the motor. Sometimes they stick.. Give it a poke to free it up.\015\012\015\012All the best,\015\012\015\012WD ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson DC23 Vacuum shut off and came on. Thought it was a problem at the electrical outlet as when moving plug it would come on again. Seen canister was full, emptied it and cyclone was quite plugged up so poked out the dirt. Had dog hairs in it as well as some ashes I had just vacuumed. Plugged unit in again and pressed switch. Will not come on. Tried another outlet. Is there a reset button somewhere or could the ashes have seized the motor. What can I try besides taking it to a repair sho


... Dyson DC23 Bagless Canister Cyclonic Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Vacuum brush Everytime I try to vacuum the vacuum makes a very loud noise and starts to shake. I'm thinking it is the vacuum brush because it feels like that's where the shaking is coming from. Could it be the brush?


Your suspision may be correct especially if vac is well used/older however may i suggest you turn vac over and investigate by removing the brush cover plate? then you may see what problem is?this could be debri trapped in roller/brush hous ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0619 seconds