Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

Progressive Kenmore hose canister connection broken 116,2341130

\015 I have a broken connection sleeve that keeps the vaacum from running. I found a replacement part online. But I have know idea about how to separate the hose and the connection piece to replace the broken connector. I see on the replacement piece that there are wires to connect also. Can a regular person do this fix?\015

Answers :

A regular person with patience can however it is tricky. Kenmore hoses have an arrow at the cuff where the corrugated hose meets the swivel elbow at the machine, and at the cuff where the handle meets the hose. If your parts fit in the handle, the cuff needs to be squeezed slightly out of round at the arrows to allow the handle to be popped out, usually by using a vice and applying a sharp blow by hand to the underside of the hand grip.
If your problem is in the lower sleeve area where dirt gets into the contacts at the machine end, there is a 1" clip with bayonets on either side. It must be compressed at the bayonets to allow the sleeve to slide off. The internal contact rings should be cleaned and polished with W/D sand paper #600 and then lubed with vaseline. Contact fingers should be spread to apply more pressure on the internal rings before reassembling in opposite order.
When in doubt Panasonic and Kenmore warranty centers will be familiar with these.
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Progressive Kenmore hose canister connection broken 116,2341130


A regular person with patience can however it is tricky. Kenmore hoses have an arrow at the cuff where the corrugated hose meets the swivel elbow at the machine, and at the cuff where the handle meets the hose. If your parts fit in the handle, the c ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore progressive canister bad connection from hose to canister


It could be, the female part of the connector is stretched open. You can usually insert something, like a dart, between the sleeve and the holder, to tighten it. If you paid with Pay Pal, see about getting your money back. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

For Kenmore 116.27514700 Progressive powermate vaccuum, how do I take apart the hose from the connection into the canister? I have a short in the hose and want to replace just the hose.


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My kenmore progressive canister vacuum's power head has stopped working. When I check for suction from the hose, it seems strong. Could it be a belt has broken? Is this a repair that I could do myself? Thank you!


... Kenmore Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

Replace hose on kenmore 3.9 canister vacuum - Kenmore 25512/ 25513 Progressive Canister Vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

My kenmore progressive canister vacuum turns on only if the hose is attached to the floorwand. It seems that the canister motor is not working because I can't hear anything coming from the caniste


If the floor wand is powered, there may be an electrical connection that is broken when the wand is disconnected. This is part of the design, not necessarily a fault ... Vacuums

Kenmore Canister Vacuum Model 116.23912300 Hose Connection Pipe (KC92PBZTZV06)


To remove the cover. There are two tabs on the connection pipe that hold the hose connector onto the connection pipe, one on each side located on the section of the connection pipe just next to where it bends. They are visible under the lip of the co ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have the upright kenmore progressive with direct drive and the filter canister stops bringing in air and picking up when hose is put into vaccum, when you remove hose and use as an attachment it starts again


Check the hose after the brushes. With this problem there is normally a clog in between where you disconnect the hose (to use attachment) and the brushes that clean the carpet. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks


Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums

I have a kemore progressive canister vacuum and the power head connects enough to the hose where the head accnoledges it's connected and the brush spins BUT i can't get it to lock in so i have


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Kenmore height adjuster broken - Kenmore 25512/ 25513 Progressive Canister Vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

Kenmore progressive canister hose cleaning


Remove hose take it outside and flush with TSP solution then rinse with water (garden hose) let dry. spackle dust and drywall dust are water soluble and will not hurt your grass. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

How to clear hose on progressive kenmore canister vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Intuition Canister vacuum Hose connection


... Kenmore Vacuums

Removal of stuck object in hose - Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum


Depending where the object is stuck a wire coat hanger might be of some help, otherwise try a borrowing a shop vac from someone and connect from the handle side of the hose, good luck ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

My miele vacuum cleaner hose has no suction - Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum


Have you tried changing your filters.? Also using genuine filters gives you much better suction ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Hi.My model 116 36933502 only works as suction hose. When I use the bottom, a loud "flapping" noise and no suction. Everything is clean. Seems like a broken diphragm or filter? Sears Kenmore Progressive Bagless Intelliclean 5 years. Thanks Kate


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Bought a Kenmore Progressive canister vacuum at a garage sale that looked in better than average condition, filters clean, new bag, all accessories intact, some debris in roller brush. problem is no suction when turned on. There does not appear to be any obstruction in hose. did not have manual


Hello,Carnister vacuum cleaners are all built with the same principle in mind. A motor \015\012generates power which powers a vacuum which, in turn, creates suction to\015\012 lift debris. The most common areas of suction loss are within ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I've had my Kenmore Progressive canister for at least several years and never had a problem. Now, the carpet head brush does not rotate, it's not getting the connection unless I push down maintaining pressure on the handle.


Hi, try pushing the reset button with a pen or paper clip. If that doesn't work, the motor may need to replaced. If the reset button is stuck, if the reset button is stuck, use a pair of tweezers to pull it back out......\01 ... Kenmore 25512/ 25513 Progressive Canister Vacuum

How do I disassemble the swivel assembly from the hose on a kenmore progressive canister vaccuum? thanks.


... Kenmore 22812 Bagged Canister Vacuum

My kenmore progressive canister vacuum won't start,any ideas, is there a fuse? it was on then just quit. I've checked all connections and made sure they are snug, and that it's still plugged in (!) model 116.


Wire broken in several place along suction tubing. Replaced tubing and works fine ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0510 seconds