Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

Beater bar rotating but now making really loud almost buzzing sound???


Answers :

It is probably a bad belt.That model uses a geared belt and you possibly have a few teeth missing on the belt.It could also be a bad brush or bad motor but less likley.Take the cover off of the power nozzle and inspect the belt.Disconnect it and look at it for missing teelh or a bad spot where they look different than the rest if this is the problem you can stop reading and just go buy a belt.Spin the brush by hand it should give very little resistance without a belt attached.If it spins freely then inspect the ends for a bad bearing.Check the plastic end caps for melting.If they look ok then try moving the brush back and forth slightly to see if the bearing has come apart.If the brush is spinning free and the ends are not showing any movement other than spinning around then inspect the area where the belt rides and make sure it is free of debris like hair and string.Finally plug in the machine with the power nozzle attached and the brush disconected and cover still off and listen to the motor in the power nozzle.If it still makes the noise it's the motor www.sewvac.com
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater bar rotating but now making really loud almost buzzing sound???


It is probably a bad belt.That model uses a geared belt and you possibly have a few teeth missing on the belt.It could also be a bad brush or bad motor but less likley.Take the cover off of the power nozzle and inspect the belt.Disconnect it and look ... Kenmore 25512/ 25513 Progressive Canister Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.


Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.


This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Oreck xl makes really loud sound and starts to smell hot when running still picks up but I am afraid I will damage something if I use it. The loud sounds gets very loud then quits for a few seconds then starts again.


... Oreck XL Ultra Bagged Upright Vacuum

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria


It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

Hi. I have a DC 24 which when brush rotates makes a very loud noise. I have replaced the brush and side bar. The side bar appears very loose. The noise stops when I switch the brush rotation off. Any ideas ?


Hi there,I'm sorry to hear you're having difficulties with your DC24. If the cleaner head seems to be making an unusual noise during use, you may want to check all the parts are correctly assembled, and that the cleaner head and brushbar are ... Dyson Ball DC24 Bagless Upright Vacuum

I have a Fein Turbo III shop vac for several years now...about a year ago, for no apparent reason it changed into a hideously LOUD beast! It's previously low decibel drone is now so loud it makes my ears ring afterwards...its sound is high pitched, almost like its hose is blocked, but it isn't...and suction remains good...I just can't take the sound...Help me.


It sounds like the bearings in the motor are shot. You can try to get a replacement motor, or if you're a mechanical genius type, you might be able to repair the motor bearings. If the shaft is worn, you'll have to buy a new motor.\015\012Y ... Fein 9-77-25 Turbo III Bagged Canister Vacuum

Loud rotating carpet brush noise: Just got my new Shark Navigator, but it makes a really loud noise when I turn it in the position to clean carpets. Is this normal?


... Shark Navigator Bagless Upright Vacuum

Sounds like the beater bar hits the front plastic makes a loud awful noise


Hi Cathy,Your DC33's brush control is designed to make a ratcheting sound to warn you if something is jamming the brush bar. You should be able to resolve this by making sure the cleaner head is free of any obstructions, and removing any thre ... Dyson DC33 Animal Bagless Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Its making this loud really loud sound when on not like normal


Clogged lines, clogged filter or hair tangled on the moving parts. Take apart and clean as needed. ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

DYSON DC14 While vacuuming the living room, the rotating brush started making an awful loud grinding sound. We opened the intake port, cleaned the brush but to no avail sound still persists once you lower the vacuum handle in an attempt to clean. Was wondering if there was anything that can be done?


Take the bottom plate off and check the belt. Also, rotate the brush by hand - it should turn with only a moderate resistance from the belt, or very little if you take the belt off. If it is hard to turn, or if the belt is stripped-out right where it ... Vacuums

Whirlpool refrigerator model #YED22DQXBW01 makes a buzzing sound when running. Sounds almost like a fan noise but ichecked that


... Vacuums

Power bar makes loud groweling sound when turning?


Ours has been doing the same thing...the beater bar end plates, black thins, and the little groove area they go into are worn of the front and rear surfaces. You could buy a new beater bar but the wear on the housing would require quite a bit of work ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar not turning, making loud sound - Dyson DC07 Bagless Upright Cyclonic Vacuum


This machine has a clutch assy. that slips and makes a loud noise\015\012when something gets stuck in the roller brush. If you have nothing stuck in the roller brush chances are the clutch is worn and needs\015\012replacing. Not an easy ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee


... Vacuums

Our beater brush makes a really loud grinding sound when turned on.


Clearly something is jammed in up under the beater brush... if not there, then follow the belt which drives it.. something is caught up for sure.Ck ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

My Dyson Root 6 made a loud banging sound, and now its motor emits a strong burning smell every time it's switched on. It runs for a second or two, making a lot of noise, and then stops. (Just bought a new battery for it, too - what a drag...) It's off warranty, and Dyson wants almost as much to fix it as a new one would cost. Is my Root 6 e-waste, or is there anything that can be done for it?


... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

My Bissell series 65832 vacuum's rotating floor brush is making a really loud noise like its hitting something when ever I turn it on. Can you tell me how I can fix .


It probably needs a new belt, unplug the unit and find the screws that hold the cover where the belt it,remove them and look at the belt.Or it could have string or something wrapped around the brushes that would need to be cut out. ... Vacuums

Morphy richards bagless cyclone 1900w upright. Hoove picks up fine but is now making a really loud whistling sound and blows out sut occasionally. Any ideas? Thanks Adele


... Morphy Richards Vacuums

My Rainbow SE powerhead suddenly started making a different noise that almost sounded like something was stuck. The brush bar was turning ok. I took the plate off and the belt was very hot but I could see nothing wrong. What could this be?


... Rainbow 75th Anniversary Canister Vacuum

I bought this vaccuum just a few months ago. Now it barely sucks anything up and it is making this very loud noise. It almost sounds like the brush is going to vibrate off. I keep thinking something is stuck in it, but I took it apart and everything seems normal. It did melt a couple of belts also.


Probably the motor is jammed or the part where it sucks up stuff its full ... Bissell 3590 CleanView Bagless Upright Vacuum

My mod. 92L3-W IS MAKING A VERY LOUD SOUND WHILE RUNNING. HAS NEW BELT AND YES IT'S KEPT CLEAN..BEATER BAR IS OK I GUESS.......


... Bissell Vacuums

Brush bar does not turn & makes a loud noise


You need to clean your roller and replace the clutch assembly that drives the belts. poorly designed vacuum with many flaws. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0733 seconds