Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

Remove powerhead case on Kenmore #116 53500300C to change belt

\015 I have lost my owner's manual and cannot seem to get the plastic case off of the powerhead in order to change the belt. Can you help?\015

Answers :

Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Remove powerhead case on Kenmore #116 53500300C to change belt


... Kenmore 25512/ 25513 Progressive Canister Vacuum

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I need to change a belt and cant remove the casing as carpet adjust is attached and cant see how the red knob is removed


... VAX Appliances Vax X3 Bagless Upright Vacuum

How to remove cover on Kenmore canister vacuum model 116 in order to change belt?


... Kenmore 35912 / 35913 Progressive Upright Vacuum

I am trying to change the belt on the featherlite dirty devil. how do you remove casing? [email protected]


... Dirt Devil M085580 Featherlite Plus Upright Vacuum

How do you change the belt on a Vax U90-MA-R vacuum. I don't seem to be able to remove the casing to get to it.


... Vacuums

Dirt is coming out the bottom of my Kenmore Progressive Upright Vacuum. My husband found a large dust bunny in the drive belt and removed it. He also changed the bag. Why is dirt coming out the bottom? Thanks.


Its still clogged, you gotta dig deeper ... Vacuums

HOW DO YOU CHANGE BELT CANT SEEM TO REMOVE BOTTOM TO GET TO IT KENMORE WISPERTONE 116


The top cover to the light lense pops off at the ends. When you get that cover off then you will see 2 screws that are by the swivel neck. Take those out and then the whole body top cover comes off. That will get you into the roller brush and belt ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?


... Eureka WhirlWind 4381 Upright Vacuum

I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym


Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

Change belt How do I change the belt. I took the bottom off and removed the roller but can't get the rest apart to get to the place to hook the belt on the the drive.


... Hoover U4270-930 Vacuum

I am smelling a faint burning rubber smell and I think the belt needs changing, but I can't figure out how to open the case to change the belt. Can you help me?


... Hoover U5068-900 Sprint Upright Vacuum

How to change the belt for kenmore heavy duty plus extra wide sweep model no. is 1163966180 looking for manual how to change the belt


... Vacuums

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Changing belt how do you remove the base to change the belt


Turn vacuum over, remove looks like 3 or 4 screws, then the top cover will come off, exposing the belt and brush roll. Part 61520 style J belt. ... Eureka 2271 Bagged Upright Vacuum

Changing a belt on a Hoover Vacuum Cleaner, Model U4264-930. can not get the old belt off.. U4264-930can not remover old belt on sweeper


... Hoover Vacuums

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum


This video shows you everything you need to know ... Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

How do I remove the roller from the hoover c1429 vacuum cleaner in order to change the belt. Thanks.


That is an elite style upright. You will need to remove the hood by releasing for tabs around the outside of the hood/base. The brush will simply lift up. You may need to pry on the base with a flat blade GENTLY to get tabs on the ends of the roller ... Hoover Vacuums

How do i change my Kenmore upright vacuum belt?


... Kenmore 33721 Upright Vacuum

Change the belt in my kenmore power-mate 120 amps...how to open it to get to where the belt is???


HELLO, JUST REPLACED THE BELT ON OUR'S. FIRST TAKE LITE LENSE OFF THERE WILL BE 2 SCREWS, REMOVE. THEN FLIP OVER POWER MITEON EACH SIDE PRY WITH 2 SCREW DRIVERS WHERE THE ARROWS ARE TO SEPERATE & THERE IT IS THE BELT. MIKE ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it


Look for grooves on the motor shaft and on the brush shaft. ... Kenmore Quick Clean 30012 Vacuum

I have a kenmore vacuum cleaner that I bought a new belt for butcannot get the bottom off to change the belt. Model # 116 53312305


... Kenmore Vacuums

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?


Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0909 seconds